background image

T02.0.3X.6C-07 

Mounting and operating manual OXY 3610 MP

  

Page 3 von 14 

 

Safety 

1.1  General note 

Read this document carefully and get used to the operation of the device before you use it. Keep this document within 
easy reach near the device for consulting in case of doubt.  

Mounting, start-up, operating, maintenance and removing from operation must be done by qualified, specially trained 
staff that have carefully read and understood this manual before starting any work. 

The manufacturer will assume no liability or warranty in case of usage for other purpose than the intended one, ignor-
ing this manual, operating by unqualified staff as well as unauthorized modifications to the device. The manufacturer is 
not liable for any costs or damages incurred at the user or third parties because of the usage or application of this de-
vice, in particular in case of improper use of the device, misuse or malfunction of the connection or of the device. Be-
stimmungsgemäße Verwendung 

1.2  Intended use 

Dissolved Oxygen-Measuring transducer converts an air oxygen-value in a 4-20 mA signal. 

1.3  Qualified staff 

For operating, running, maintaining and commissioning the device, the staffs needs to have an adequate level of 
knowledge of both, the measuring and the meaning of measured values. This manual can be a valuable contribution. 
All instructions have to be well-understood and complied with. To be sure that there is no risk arising due to misinter-
pretation of measured values, the operator must have further knowledge in case of doubt - the user is liable for any 
harm/damage resulting from misinterpretation due to insufficient knowledge.  
The manufacturer will assume no liability or warranty in case of usage for other purpose than the intended one, ignor-
ing this manual, operating by unqualified staff as well as unauthorized modifications to the device. 

1.4  Safety signs and symbols 

Warning notices are marked in this manual as shown below: 

 

This symbol warns of imminent danger, death, serious injuries and significant damage to prop-
erty at non-observance.

 

 

This symbol warns of danger to living tissue and many materials, that can be damaged 
or destroy by exposure to that chemical! 

 

Achtung! Symbol warnt vor möglichen Gefahren oder schädlichen Situationen, die bei Nichtbe-
achtung Schäden am Gerät bzw. an der Umwelt hervorrufen.

 

 

This symbol points out processes which can indirectly influence operation or provoke unfore-
seen reactions at non-observance.

 

 

This symbol refers of using a eye protection, which protects the eyes from strong light, UV radia-
tion, laser, chemicals, dust, splitter or weather conditions. 

 

This symbol refers of using protective gloves, which protects for mechanical-, thermal-, chemi-
cal-, biological- or electrical hazards. 

 

 

Содержание OXY 3610 MP















Отзывы: