background image

8

1)    The battery pack for this tool has been shipped in a 
       low charge condition. You should charge the battery 
       pack fully before use.

2)    To ensure the longest battery life and best battery 
       performance, always charge the battery when the air 
       temperature is between 18-24

0

C (65-75

0

F). Do not 

       charge the battery pack when the temperature is 
       below 4ºC (40

0

F),or above 40

0

C (104

0

C). This is 

       important. Failure to observe this safety rule could 
       cause serious damage to the battery pack.

3.

Important safety instructions for battery packs

APPLICATION

  8)  Do not place any object on top of the charger as it 
       could cause overheating. Do not place the charger 
       near any heat source.

9)    Do not pull on the plug of the charger to disconnect 
       it from the power source.

10)  Make sure that the charger cable is positioned where 
       it will not be stepped on, tripped over or otherwise 
       subjected to damage or stress.

11)  Do not use an extension cord unless it is absolutely 
       necessary. The use of an improper extension cord 
       could cause the risk of fire, electric shock or 
       electrocution.

12)  Do not use the charger if it has been subjected to a 
       heavy knock, dropped or otherwise damaged in any 
       way. Take the charger to an authorized service centre 
       for a check or repair.

13)  Do not disassemble the charger. Take it to an 
       authorized service centre when service or repair is 
       required. Incorrect re-assembly may result in the risk 
       of fire, electric shock or electrocution.

14)  To reduce the risk of an electric shock, unplug the 
       charger from the power supply before attempting to 
       clean it. Removing the battery alone does not reduce 
       the risk.

15)  Do not store or use the tool and battery pack in 
       locations where the temperature may reach or exceed 
       40

0

C (104

0

F) such as alongside sheds or metal 

       structures in the summer.

16)  The charger is designed for use from a standard 
       household electrical supply (120V). Do not attempt 
       to connect the charger to a different supply.

17)  If you wish to charge a second battery pack, unplug 
       the charger from the main supply and leave it for at 
       least 15 minutes. After this time you can charge a 
       second battery pack.

3)    Do not incinerate the battery pack even if it is seriously 
       damaged or can no longer hold a charge. The battery 
       pack can explode in a fire.

4)    A small leakage of liquid from the battery pack may
       occur under extreme usage or temperature conditions. 
       This does not necessarily indicate a failure of the 
       battery pack. However, if the outer seal is broken and 
       this leakage comes into contact with your skin:
       - wash the affected area quickly with soap and water.
       - neutralize the liquid with a mild acid such as lemon
       juice or vinegar.
       If the leakage gets in your eyes:
       - flush your eyes with clean water for a minimum of 
      10 minutes and seek immediate medical attention. 
       Inform the medical staff that the liquid is a 25-35% 
       solution of potassium hydroxide.

5)    Never attempt to open the battery pack for any reason. 
       If the plastic housing of the battery pack breaks open 
       or cracks, immediately discontinue its use and do 
       not recharge it.

6)    Do not store or carry a spare battery pack in a pocket, 
       toolbox or any other place where it may come into 
       contact with metal objects. The battery pack may be 
       short circuited causing damage to the battery pack, 
       burns or a fire.

7)    The battery pack utilizes nickel-cadmium cells. 
       Cadmium is considered to be a toxic material.

8)    Use an environmentally safe disposal unit at a municipal 
       waste disposal centre to dispose of a damaged or 
       worn out battery, or return it to your dealer.

Intended Use

This GREEN-TECH impact wrench is intended for driving
in and loosening screws as well as for drilling in wood, 
metal, ceramic and plastic.

Check the package contents

Carefully remove each tool in the kit from the packaging. 
The kit includes:

--Cordless drill

- Cordless impact driver

--2 pcs rechargeable battery packs
--Battery charger

If any parts are missing or damaged, please contact 
Customer service at 800-832-7168.

ENGLISH

F

Содержание 02325010
























Отзывы: