Greenheck DGX Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 48

Greenheck DGX Скачать руководство пользователя страница 48

Warranty

Greenheck warrants this equipment to be free from defects in material and workmanship for a period of one year from
the purchase date. Any units or parts which prove defective during the warranty period will be replaced at our option
when returned to our factory, transportation prepaid.

Motors are warranted by the motor manufacturer for a period of one year. Should motors furnished by Greenheck
prove defective during this period, they should be returned to the nearest authorized motor service station. Greenheck
will not be responsible for any removal or installation costs.

As a result of our commitment to continuous improvement,

Greenheck reserves the right to change specifications without notice.

This manual is the property of the owner, and is required for future maintenance.

Please leave it with the owner when you complete the job.

DG/DGX (Direct Spark) IOM FS

Rev 2 May 2005

Copyright © 2005 Greenheck Fan Corp.

GREENHECK

P.O. BOX 410 SCHOFIELD, WISCONSIN 54476-0410

PH. 715-359-6171

www.greenheck.com

«
...
46
47
48

Содержание DGX

















































Отзывы:

Нет отзывов