Greenheck DGX Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 48

Greenheck DGX Скачать руководство пользователя страница 27

27

NOTE!

The minimum cooling temperature is preset to the factory recommended 75ºF. Steps 5-7 should only

be complete if the minimum cooling temperature needs adjustment.

NOTE!

The inlet air sensor function overrides and shuts down the evaporative cooler if the outside

temperature falls below the minimum cooling temperature.

Step 5 Enter Program Mode

Press and hold the Enter Key for three seconds.
The display will read “Pro” when Program Mode is
active. See figure #54.

Start-Up - Water Wizard™ (Optional)

NOTE!

The manual supply valve ships closed and must be

adjusted for proper performance.

Step 2 Set the Water Pressure

With the solenoid open, set the supply
water pressure to the correct setting from
table 2. Use the manual supply valve to
adjust the supply pressure. A pressure
gauge is provided between the manual
supply valve and the media. See figure #53.

Step 3 Close Solenoid

With the pressure set, press the Function
Key for one second to deactivate Flow Test
Mode and allow the supply solenoid to
close.

Step 4 Check Media

Start the cooling cycle and check the media after one hour of operation. If the media is continuously
dry or if too much water is draining from the sump tank, refer to the Trouble Shooting section.

Water Pressure

(in. w.c.)

MSU 12

20

MSU 22 (43

3

⁄

4

in. wide*)

36

MSU 22 (48 in. wide*)

42

MSU 22 (60 in. wide*)

61

MSU 32 (66 in. wide*)

72

MSU 32 (96 in. wide*

+

)

42

MSU 35

61

MSU 38

37

MSU 42

51

*Total media width

+

Two 48 inch media sections

Step 1 Open the Solenoid

Confirm that the manual water supply valve is closed. Press and hold the Function Button for one
second. L3 will begin blinking (short on, long off), indicating that Flow Test Mode is active and the
supply solenoid is open.

Figure 54.

Program Display

Drain Solenoid

Supply

Solenoid

Manual

Supply Valve

Pressure

Gauge

To Media

Sump

Drain

Roof

Line

Trap

Figure 53.

Water Wizard Installation

Start-Up

Table 2.

Recommended Water Pressure

«
...
25
26
27
28
29
...
»

Содержание DGX

















































Отзывы:

Нет отзывов