manualshive.com logo in svg

Greenheck DGX, Инструкция по установке, эксплуатации и обслуживанию, Страница: 38 / 48

Поделиться
Скачать
Greenheck DGX Скачать руководство пользователя страница 38

38

Maintenance - Routine

CAUTION!

Lock-out the gas and the electrical power to the unit before performing any maintenance or service

operations to this unit.

IMPORTANT!

Do not install new belts on worn

sheaves.  If the sheaves have

grooves worn in them, they must

be replaced before new belts are

installed.

IMPORTANT!

Premature or frequent belt failures can be caused by

improper belt tension, or misaligned sheaves.

Abnormally low belt tension

will cause squealing on

start-up, excessive belt

flutter, slippage and

overheated sheaves

Abnormally high belt tension

or drive misalignment will

cause excessive bearing

loads and may result in
failure of the fan and/or

motor bearings.

IMPORTANT!

When replacing V-belts on

multiple groove drives all belts

should be changed to provide

uniform drive loading.

Belt  Span

Deflection = 

Belt  Span

64

IMPORTANT!

Do not pry belts on or off the

sheave.  Loosen belt tension until

belts can be removed by simply

lifting the belts off the sheaves.

V-Belt Drives

V-belt drives must be checked on a regular basis for
wear, tension, alignment and dirt accumulation.

Check the tension by measuring the deflection in the
belt as shown in figure #62.

Check the alignment by using a straight edge across
both sheaves as shown in figure #63.

Maintenance

Figure 62.  

Belt tension

Figure 63.  

Drive Alignment

Содержание DGX

















































Отзывы:

Нет отзывов