Greenheck DGX Скачать руководство пользователя страница 1

Part # 464043

®

**WARNING**

Disconnect and secure all electrical power to the

“OFF” position prior to inspection or servicing.

Failure to comply with this safety precaution

could result in serious injury or death.

**IMPORTANT**

All factory provided lifting lugs must be used when lifting any unit. Failure to comply with this safety

precaution could result in property damage, serious injury or death.

FOR YOUR SAFETY

If you smell gas
1.  Open windows
2.  Don’t touch electrical switches
3. Extinguish any open flames
4.  Immediately call your gas supplier

Report any damaged equipment to the shipper immediately!

All units are shipped on a skid or packaged to minimize damage during shipment. The transporting carrier has
the responsibility of delivering all items in their original condition as received from Greenheck. The individual
receiving the equipment is responsible for inspecting the unit for obvious or hidden damage, recording any
damage on the bill of lading before acceptance and filing a claim (if required) with the final carrier. Some
accessory items are stored inside the unit during shipping. Care must be taken during installation to prevent
damage to units.

FOR YOUR SAFETY

The use and storage of gasoline or other

flammable vapors and liquids in open

containers in the vicinity of this appliance

is hazardous.

**WARNING**

Improper installation, adjustment, alteration,

service or maintenance can cause property

damage, injury or death. Read the installation,

operating, and maintenance instructions

thoroughly before installing or servicing this

equipment.

Maintenance

Troubleshooting

Operation

Start-Up

Installation

Reference

MODEL DG / DGX (Direct Spark) 

Make-Up Air Unit 

Installation, Operation and Maintenance Manual

Содержание DGX

















































Отзывы: