background image

Specifications

15

Physical:
Dimensions:

  

145mm x85mm x30mm

Weight:   

400g

Connectors:

  

1x Neutrik XLR 4 pin, 1x miniUSB 

Mounting:  

Beltclip

Power:    

1800mAh Lithium-Ion rechargeable battery.

Troubleshooting

There is no signal or poor signal level to the belt-pack 

- Check Pairing with Antenna 
- Check you are within range (300 metres maximum with clean line of sight)
- Ensure that the antenna is vertically orientated

The antenna is not sending a signal 

- Check that the LED is not flashing red and green. 
This means that there is no other device on the system or that the antenna is not configured to the 
network configuration.

I am unable to communicate with other units 

- Make sure you are using the same configuration file on all units
- If you go to the setup menu/clone config and check to see if more than one config is available.

There is an echo on the system

- Establish if any microphones are open close to speakers.

I am trying to pair my beltpack over the air with more than one antenna, but it will only connect to the first one 

- When doing over the air pairing make sure the beltpack is not connected to another antenna. 
  Switch of other antennas that it has been paired to.

My beltpack looses contact to the antenna when either the antenna or the beltpacks are very close together. 

- Having 2 RF (radio frequency) devices next to one another can have an influence on RF behavior. 
  They should be at least1 meter (3 feet) apart.

...continues

Green Go Wireless Beltpack

model nr. GGO-WBPX

User guide

GO

COMMUNICATION

Connector Pin assignments:

Pin 1: MIC Ground
Pin 2: MIC Signal
Pin 3: Speaker  -
Pin 4: S 

HEADSET

Содержание GGO-WBPX
















Отзывы: