Gree Hydro Box NRQR16L/A-T Скачать руководство пользователя страница 33

Страница: 33 / 36

Hydro Box

4.8.5 Water discharge of hydro box

) Use a screwdriver to unscrew the 9 screws of the top cover of the hydro box and the 4

screws at the bottom of the rear panel (the side panel without the GREE logo), and then
remove the top cover and the rear panel;

Fig.4.23

(2) Operate from the direction shown in the figure below. Loosen the drain valve and the
exhaust valve installed on the outlet water pipe.

Fig.4.24

(3) Start draining and finish draining when no water comes out of the drain valve.

Notes:

①

Extra drain valve of external water pipe must be installing to ensure that the water in the

whole circulating water system can be completely drained.

②

Please open the discharge valve A and water discharge valve B connected to the outside

of the hydro box at the same time when draining of hydro box.

Содержание Hydro Box NRQR16L/A-T





































Результаты поиска

Содержание Hydro Box NRQR16L/A-T

Отзывы:

Похожие инструкции для Hydro Box NRQR16L/A-T

Бренды по названию

Популярные бренды

Gree Hydro Box NRQR16L/A-T, Руководство пользователя

Результаты поиска

Содержание Hydro Box NRQR16L/A-T

Отзывы:

Похожие инструкции для Hydro Box NRQR16L/A-T

Бренды по названию

Популярные бренды