Gree HW18024PNa-D Скачать руководство пользователя страница 3

Unitary Ducted Split AC

1

Safety Considerations

Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, 

fire, electrical shock, or other conditions which may cause death, personal injury, or property 
damage. Consult a qualified installer, service agency, or your distributor or branch for information or 
assistance. The qualified installer or agency must use factory--authorized kits or accessories when 
modifying this product. Refer to the individual instructions packaged with the kits or accessories 
when installing. Follow all safety codes. Wear safety glasses, protective clothing, and work 
gloves. Use quenching cloth for brazing operations. Have fire extinguisher available. Read these 
instructions thoroughly and follow all warnings or cautions included in literature and attached to 
the unit. Consult local building codes and National Electrical Code (NEC) for special requirements. 
Recognize safety information. This is the safety--alert symbol .When you see this symbol on the 
unit and in instructions or manuals, be alert to the potential for personal injury. Understand these 
signal words; DANGER, WARNING, and CAUTION. These words are used with the safety--alert 
symbol. DANGER identifies the most serious hazards which will result in severe personal injury 
or death. WARNING signifies hazards which could result in personal injury or death. CAUTION is 
used to identify unsafe practices which may result in minor personal injury or product and property 
damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, 
or operation.

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury or death.
Before installing, modifying, or servicing system,main electrical disconnect switch must be in 

the OFF position. There may be more than 1 disconnect switch. Lock out and tag switch with a 
suitable warning label.

This product must not be disposed together with the domestic waste. 
This product has to be disposed at an authorized place for recycling of 
electrical and electronic appliances. 

Содержание HW18024PNa-D

























Отзывы: