background image

DC Inverter Multi VRF System   

21 

5 Check Items after Installation and Test Operation 

5.1 Check Items after Installation 

Check items 

Possible conditions due to improper installation 

Check 

Each part of the unit is installed securely? 

Unit may drop, shake or emit noise. 

 

Gas leakage test is taken or not? 

Insufficient cooling (heating) capacity. 

 

Unit gets proper thermal insulation or not? 

There may be condensation and dripping. 

 

Drainage is smooth or not? 

There may be condensation and dripping. 

 

Is the voltage in accordance with the rated voltage 
specified on the nameplate? 

Unit may have malfunction or components may 
get damaged. 

 

Is the electric wiring and pipe connection installed 
correctly? 

Unit may have malfunction or components may 
get damaged. 

 

Unit is securely grounded or not? 

Electrical leakage. 

 

Power cord meets the required specification? 

Unit may have malfunction or components may 
get damaged. 

 

Is the air inlet/outlet blocked? 

Insufficient cooling (heating) capacity. 

 

Length of refrigerant pipe and the charging amount 
of refrigerant are recorded or not? 

The refrigerant charging amount is not 
accurate. 

 

Binding pieces on compressor feet are removed or 
not? 

Compressor may get damaged. 

 

5.2 Test Operation and Debugging 

 

(1)  After finishing the first installation or replacing the main board of outdoor unit, it is necessary to perform test 

operation and debugging. Otherwise, unit won’t be able to work. 

(2)  Test operation and debugging must be performed by professional technicians or under the guidance of 

professional technicians. 

5.2.1 Prepare the Test Operation and Debugging 

(1)  Do not connect power until all installation work is finished. 
(2)  All control circuits and wires are correctly and securely connected. 
(3)  Check whether the fixing loops for compressor foots are removed. 
(4)  All small pieces, especially metal chips, thread ends and forceps holder, must be removed 

from the unit. 

(5)  Check whether unit’s appearance and pipeline system has been damaged during 

transportation. 

(6)  Calculate the quantity of refrigerant that needs to be added according to the pipe length. 

Pre-charge the refrigerant. In case that the required charging quantity is not reached while 
refrigerant can’t be added, record the quantity of refrigerant that still needs to add and 
complement the quantity during test operation. For details of adding refrigerant during test 
operation, see below. 

(7)  After refrigerant is added, make sure valves of outdoor unit are completely open. 
(8)  For the convenience of troubleshooting during debugging, unit shall be connected to a PC 

with applicable debugging software. Make sure unit’s real-time data can be checked through 
this computer. The installation and connection of debugging software can be found in the 
Service Manual. 

Содержание GMV-36WL/C-T





































Отзывы: