Gree GKH18K3HI Скачать руководство пользователя страница 37

Страница: 37 / 40

Cassette Type Air Conditioner Unit

Note:

①

. The design of this unit conforms to the requirements of ISO5151standard.

②

. The air volume is measured at the relevant standard external static pressure.

③

. Cooling (heating) capacity stated above is measured under nominal working conditions

corresponding to standard external static pressure. The parameters are subject to change with the

improvement of products, in which case the values on nameplate shall prevail.

④

. In this table, there are two outside DB values under the low temp cooling conditions, and the one in

the brackets is for the unit which can operate at extreme low temperature.

7 Troubleshooting and Maintenance

7.1 Troubleshooting

If your air-conditioning unit suffers from abnormal operation or failure, please first

check the following points before repair:

Table 7.1

Failure

Possible Reasons

The unit cannot be

started.

①

. The power supply is not connected.

②

. Electrical leakage of air-conditioning unit causes tripping of the leakage

switch.

③

. The operating keys are locked.

④

. The control loop has failure.

The unit operates for a

while

and then stops.

①

. There is obstacle in front of the condenser.

②

. The control loop is abnormal.

③

. Cooling operation is selected when the outdoor ambient temperature is

above 48°C.

Poor cooling effect.

①

. The air filter is dirty or blocked.

②

. There is heat source or too many people inside the room.

③

. The door or window is open.

④

. There is obstacle at the air intake or outlet.

⑤

. The set temperature is too high.

⑥

. There is refrigerant leakage.

⑦

. The performance of room temperature sensor becomes worse

Poor heating effect

①

. The air filter is dirty or blocked.

②

. The door or window is not firmly closed.

③

. The set room temperature is too low.

④

. There is refrigerant leakage.

⑤

. The outdoor ambient temperature is lower than -5°C.

⑥

. Control loop is abnormal.

Note:

After carrying out the check of the above items and taking relevant measures to solve the

problems but the air-conditioning unit still does not function well, please stop the operation of the unit

immediately and contact the local service agency designated by Gree. Only ask professional serviceman

to check and repair the unit.

Содержание GKH18K3HI









































Результаты поиска

Содержание GKH18K3HI

Отзывы:

Похожие инструкции для GKH18K3HI

Бренды по названию

Популярные бренды

Gree GKH18K3HI, Руководство пользователя

Результаты поиска

Содержание GKH18K3HI

Отзывы:

Похожие инструкции для GKH18K3HI

Бренды по названию

Популярные бренды