Gree GKH18K3HI Скачать руководство пользователя страница 11

Страница: 11 / 40

Cassette Type Air Conditioner Unit

cooling and heating effect performs.

3.4 Electrical Requirement

Electric Wire Size and Fuse Capacity.

Table 3.5

Indoor Units

Power Supply

Breaker Capacity

Min. Power Supply

Cord

V/Ph/Hz

18K~60k

220-240V~ 50Hz

1.0

Table 3.6

Outdoor Units

Power Supply

Fuse Capacity

Capability of Air

Switch

Minimum Sectional
Area Of Earth Wire

V/Ph/Hz

GUHN18NK3HO

220-240V ~ 50Hz

2.5

GUHN24NK3HO

4.0

GUHN30NK3HO

4.0

GUHN36NM3HO

380-415V 3N

～

50Hz

1.5

GUHN42NM3HO

2.5

GUHN48NM3HO

2.5

GUHN60NM3HO

2.5

Notes:

①

. The fuse is located on the main board.

②

. Install the disconnect device with a contact gap of at least 3 mm in all poles

nearby the units (Both indoor unit and outdoor unit).The appliance must be

positioned so that the plug is accessible.

③

. The specifications of the breaker and power cable listed in the Table above are

determined based on the maximum power (maximum amps) of the unit.

④

. The specifications of the power cable listed in the Table above are applied to the

conduit-guarded multi-wire copper cable (like, YJV copper cable, consisting of PE

insulated wires and a PVC cable jacket) used at 40°С and resistible to 90°С (see

IEC 60364-5-52). If the working condition changes, they should be modified

according to the related national standard.

⑤

. The specifications of the breaker listed in the Table above are applied to the

breaker with the working temperature at 40°С. If the working condition changes,

Содержание GKH18K3HI









































Результаты поиска

Содержание GKH18K3HI

Отзывы:

Похожие инструкции для GKH18K3HI

Бренды по названию

Популярные бренды

Gree GKH18K3HI, Руководство пользователя

Результаты поиска

Содержание GKH18K3HI

Отзывы:

Похожие инструкции для GKH18K3HI

Бренды по названию

Популярные бренды