Gree GKH18K3HI Скачать руководство пользователя страница 8

Страница: 8 / 40

Cassette Type Air Conditioner Unit

Table 3.2

Outdoor Unit Accessories

No.

Name

Appearance

Q'ty

Usage

Drain Plug

2or3

To plug the unused drain hole.

Drainage Connecter

To connect with the hard PVC
drain pipe

3.2 Selection of the Installation Location

WARNING!

The unit must be installed where strong enough to withstand the weight of the unit and fixed
securely, otherwise the unit would topple or fall off.

CAUTION!

①

. Do not install where there is the danger of combustible gas leakage.

②

. Do not install the unit near heat source of heat, steam, or flammable gas.

③

. Children under 10 years old must be supervised not to operate the unit.

④

. The appliance shall not be installed in the laundry.

Decide the installation location with the customer as follows:

3.2.1 Indoor Unit

Select an installation site where the following conditions are fulfilled and that meets

your customer's approval.

(1). Obstruct should be put away from the intake or outlet vent of the indoor unit so

that the airflow can be blown through all the room.

(2). Make sure that the installation meets the requirement of the schematic diagram of

installation spaces.

(3). Select the place where can stand 4 times of the weight of the indoor unit and

would not increase the operating noise and vibration.

(4). The horizontality of the installation place should be guaranteed.

(5). Select the place where is easy to drain out the condensate water, and connect

with outdoor unit.

(6). Make sure that there are enough space for care and maintenance, and the height

Содержание GKH18K3HI









































Результаты поиска

Содержание GKH18K3HI

Отзывы:

Похожие инструкции для GKH18K3HI

Бренды по названию

Популярные бренды

Gree GKH18K3HI, Руководство пользователя

Результаты поиска

Содержание GKH18K3HI

Отзывы:

Похожие инструкции для GKH18K3HI

Бренды по названию

Популярные бренды