manualshive.com logo in svg

Gree CB385001000, Руководство по обслуживанию

Поделиться
Скачать
Gree CB385001000 Скачать руководство пользователя страница 81

78

Installation and Maintenance

Service Manual

3. High temperature and overload protection diagnosis (AP1 hereinafter refers to the control board of the outdoor 
unit)

Mainly detect:

●Is outdoor ambient temperature in normal range?
●Are the outdoor and indoor fans operating normally?
●Is the heat dissipation environment inside and outside the unit good?

Fault diagnosis process:

End

Yes

No

Yes

No

Yes

No

Overheat and high 

temperature protection

Is outdoor ambient temperature higher than 53?

20 minutes after the complete 

unit is powered off.

Is heat dissipation of the indoor unit 

and outdoor unit abnormal?

Normal protection, please operate 

it after the outdoor ambient temp-

erature is normalized.

Improve the heat 

dissipation environ-

ment of the unit

Does the outdoor fan work normally?

1. Check if the fan terminal OFAN 

is connected correctly

2. Resistance between any two 

terminals is measure by an ohm 

gauge and should be less than 1K 

Ohm.

Replace the  

control panel 

AP1

Replace the fan 

capacitor C1

Replace the 

outdoor fan

Содержание CB385001000









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды