background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of purchase.

This warranty does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability exceed the
original cost of the purchased kit. 
Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted for
any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product, the user
accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit
immediately in new and unused condition to the place of purchase.

IMPORTANT NOTE: This model is designed for sport flying and AMA Quickie 500 racing. We will not quote all of the
AMA regulations for Quickie 500 racing in this manual. Any information provided here regarding racing is provided for
informational purposes only and is NOT guaranteed to be accurate. Only the printed version of the AMA regulations
should be used in case of protests or other disputes involving events covered by the regulations.

READ THROUGH THIS  MANUAL  BEFORE  STARTING
CONSTRUCTION.

IT CONTAINS IMPORTANT

INSTRUCTIONS  AND WARNINGS  CONCERNING THE
ASSEMBLY AND USE OF THIS MODEL.

GPMZ0203 for GPMA1265/1266  V1.0

Entire Contents © Copyright 2003

Champaign, IL

(217) 398-8970, Ext. 5

[email protected]

INSTRUCTION MANUAL

Wingspan: 52 in [1320mm] 
Wing Area: 504 sq in [33dm²] 
Weight: 3.5 lbs - 4 lbs [1360 - 1530g] 
Wing Loading: 14 - 15 oz/sq ft [42 - 47 g/dm²] 
Length: 41-1/4 in [1048mm] 
Engine: .25 - .46 cu in [4.0 - 7.5cc] two-stroke

Содержание Viper 500 ARF

























Отзывы: