background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of purchase.

This warranty does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability exceed the
original cost of the purchased kit. 
Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted for
any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product, the user
accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit
immediately in new and unused condition to the place of purchase.

READ THROUGH THIS MANUAL BEFORE STARTING
CONSTRUCTION.

IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING
THE ASSEMBLY AND USE OF THIS MODEL.

OLD4P03 for GPMA0495  V1.0

Entire Contents © Copyright 2002

1610 Interstate Drive Champaign, IL 61822

(217) 398-8970, Ext. 2

[email protected]

INSTRUCTION MANUAL

Wingspan: 73 in [1854mm]
Wing Area: 735 sq in [47 dm

2

]

Weight: 5-1/4 lb [2434 g]
Wing Loading: 17 oz/sq ft [52 g/dm

2

]

Fuselage Length: 55 in [1397mm]
Radio: 3-Channel
Engine: .30 – .40 cu in two-stroke,

.40 – .52 cu in four-stroke

Содержание Old Timer















































Отзывы: