manualshive.com logo in svg

GREAT PLAINS Yield-Pro 3P3025AH, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Yield-Pro 3P3025AH Скачать руководство пользователя страница 98

Great Plains

 | 411-332M | 2019-02-19

Table of Contents

Index

94

3P3025AH

Table of Contents

Index

Maintenance

Speed Sensor Gaps, Hydraulic Drive

Refer to Figure 114

1. Make sure a tooth on the sensor sprocket  is

aligned with the sensor .

2. Check that wheel teeth are on sensor wheel

side-to-side. If adjustment is needed, loosen the top

jam nut  on sensor. Adjust the position of the

sensor and tighten the top jam nut.

3. Check gap  between end of sensor and tooth on

the sensor sprocket. The gap must be

1

/

16

inch (1.6 mm).

To adjust, loosen both jam nuts. Adjust the jam nuts

to set gap. Tighten jam nuts without changing the

gap.

Chain Maintenance

Inspect and lubricate chains regularly. The slack of new

chains tends to increase during the first few hours of

operation due to seating.

Chain Slack

Check chain slack within the first 8 hours of operation

and adjust as necessary. Check slack at spring-operated

idlers seasonally.

Refer to Figure 116, which, for clarity, greatly 

exaggerates slack, and omits the idlers.

1. Measure the span

 for allowable slack:

Locate the longest span of each chain (usually the

span which does not run through the idlers).

2. Determine the ideal slack:

Long chains (over 36 inch/91 cm):

1

/

4

inch per foot.

Vertical short chains:

1

/

4

inch per foot (2.1 cm/m).

Horizontal short chains:

1

/

2

inch per foot (4.2 cm/m).

3. Measure the current slack

:

Acting at a right angle to the chain span at the center

of the span, deflect the chain in both directions. The

slack is the distance of the movement.

4. Adjust the idlers for ideal slack.

Chain Clips

Whenever mounting a chain, make sure the clip at the

removable link is oriented to minimize snags.

Refer to Figure 117 (arrow shows chain direction)

Install clip with open end facing away from direction of

chain travel (shown by gray or striped arrows in chain

routing diagrams).

Figure 115

Hydraulic Drive Sensor Gap 

(Shield removed for clarity)

68093

A

2

1

3

1

2

3

A

Figure 116

Measuring Chain Slack

27264

2

1

1

Figure 117

Chain Clip Orientation

26482

2

Содержание Yield-Pro 3P3025AH
























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды