manualshive.com logo in svg

GREAT PLAINS Ultra-Till I 3030 Series, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Ultra-Till I 3030 Series Скачать руководство пользователя страница 7

UT3030-UT5052

Table of Contents

Index

Important Safety Information

Great Plains

 | 576-026M-A | 05/11/2021

Table of Contents

Index

5

Transport Machinery Safely

Maximum transport speed for implement is 20 mph (32 kph),

13 mph (22 kph) in turns. Some rough terrains require a slower

speed. Sudden braking can cause a towed load to swerve and

upset. 

Do not exceed 20 mph. Never travel at a speed which does

not  allow  adequate  control  of  steering  and  stopping.

Reduce speed if towed load is not equipped with brakes.

Comply with state and local laws.

Do not tow an implement that, when fully loaded, weighs

more than 1.5 times the weight of towing vehicle.

Carry  reflectors  or  flags  to  mark  Ultra-Till  in  case  of

breakdown on the road.

Keep  clear  of  overhead  power  lines  and  other

obstructions  when  transporting.  Refer  to  transport

dimensions under “

UT Specifications and Capacities

” on

page 26.

Do  not  fold  or  unfold  the  Ultra-Till  while  the  tractor  is

moving

Shutdown and Storage

Lower Ultra-Till, put tractor in park, turn off engine, and

remove the key.

Secure Ultra-Till using blocks and supports provided.

Detach  and  store  machine  in  an  area  where  children

normally do not play.

Tire Safety

Tire changing can be dangerous and should be performed by

trained personnel using correct tools and equipment.

When  inflating  tires,  use  a  clip-on  chuck  and  extension

hose long enough for you to stand to one side–not in front

of or over tire assembly. Use a safety cage if available.

When removing and installing wheels, use wheel-handling

equipment adequate for weight involved.

Содержание Ultra-Till I 3030 Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды