manualshive.com logo in svg

GREAT PLAINS Ultra-Till I 3030 Series, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Ultra-Till I 3030 Series Скачать руководство пользователя страница 29

UT3030-UT5052

Table of Contents

Index

Appendix

Great Plains

 | 576-026M-A | 05/11/2021

Table of Contents

Index

27

Hydraulic Connectors and Torque

Refer to Figure 16 (a hypothetical fitting)

Leave any protective caps in place until immediately prior to

making a connection.

1

NPT

 - National Pipe Thread

Note tapered threads, no cone/flare, and no O

-

ring.

Apply liquid pipe sealant for hydraulic applications.

Do not use tape sealant, which can clog a filter and/or plug an 

orifice.

2

JIC

 - Joint Industry Conference (SAE J514)

Note straight threads (4) and the 37

cone (5) on “M” fittings (or 

37

flare on “F” fittings).

Use no sealants (tape or liquid) on JIC fittings.

3

ORB

 - O

-

Ring Boss (SAE J514)

Note straight threads (5) and elastomer O

-

Ring (7).

Prior to installation, to prevent abrasion during tightening, 

lubricate O

-

Ring with clean hydraulic fluid.

Use no sealants (tape or liquid) on ORB fittings.

ORB fittings that need orientation, such as the ell depicted, also 

have a washer (8) and jam nut (9) (“adjustable thread port stud”). 

Back jam nut away from washer. Thread fitting into receptacle 

until O

-

Ring contacts seat. Unscrew fitting to desired orientation. 

Tighten jam nut to torque specification.

2

5

4

9

8

7

5

3

Figure 16

Hydraulic Connector ID

31282

Fittings Torque Values

Dash 

Size

Fitting

N-m

Ft-Lbs

-4

1

4

-18 NPT

1.5-3.0 turns past finger tight

-5

1

2

-20 JIC

19-20

14-15

-5

1

2

-20 ORB w/jam nut

12-16

9-12

-5

1

2

 -20 ORB straight

19-26

14-19

-6

5

16

-18 JIC

24-27

18-20

-6

5

16

-18 ORB w/jam nut

16-22

12-16

-6

5

16

-18 ORB straight

24-33

18-24

-8

3

4

 -16 JIC

37-53

27-39

-8

3

4

 -16 ORB w/jam nut

27-41

20-30

-8

3

4

-16 ORB straight

37-58

27-43

1

Содержание Ultra-Till I 3030 Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды