GREAT PLAINS Ultra-Till I 3030 Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

GREAT PLAINS Ultra-Till I 3030 Series Скачать руководство пользователя страница 18

Great Plains

| 576-026M-A | 05/11/2021

Table of Contents

16

UT3030-UT5052

Table of Contents

Preparation and Setup

Hydraulic Hose Hookup

Great Plains hydraulic hoses are color coded to help you

hookup hoses to your tractor outlets. Hoses that go to the same

remote valve are marked with the same color.

Refer to Figure 5

Hose Handles

To distinguish hoses on the same hydraulic circuit, refer to,

Hydraulic Hose Hookup above. The hose under an extended

symbol feeds a cylinder base end. The hose under a retracted-

cylinder symbol feeds a cylinder rod end.
Clean all hydraulic couplings and hook hoses to tractor.

First Time Field Adjustments

Pre-Leveling of Machine

Front to Rear Leveling

Refer to Figure 6
Front to rear leveling should be done in the field with modules

installed. This is adjusted at the turnbuckle (1) with turnbuckle

wrench (2) located on the inside, left side of hitch.

Color

Hydraulic Function

Black

Lift (2 hoses)

Green

Fold/Hydraulic Down Pressure (2 hoses)

Red

Gangs (2 hoses)

High Pressure Fluid Hazard:

Relieve pressure before disconnecting hydraulic lines. Use

paper or cardboard, NOT BODY PARTS, to check for leaks.

Wear protective gloves and safety glasses or goggles when

working with hydraulic systems. Escaping fluid under pressure

can have sufficient pressure to penetrate the skin causing

serious injury. If an accident occurs, seek immediate medical

assistance from a physician familiar with this type of injury.

Only trained personnel should work on system hydraulics.

Figure 5

Hose Handles

25463

Figure 6

Hitch Turnbuckle Adjustment

43184

1

2

«
...
16
17
18
19
20
...
»

Содержание Ultra-Till I 3030 Series





































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды