manualshive.com logo in svg

GREAT PLAINS Ultra-Till I 3030 Series, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Ultra-Till I 3030 Series Скачать руководство пользователя страница 21

UT3030-UT5052

Table of Contents

Index

Operating Instructions

Great Plains

 | 576-026M-A | 05/11/2021

Table of Contents

Index

19

General Operation and In-Field Adjustments

10. The Ultra-Till is designed as a primary/secondary vertical

tillage  tool  and  is  designed  to  leave  a  finished  seedbed

following some form of fall or spring tillage. In a min-till/

no-till  operation,  it  may  be  used  as  a  primary  one  pass

vertical tillage tool. For best results, if at all possible, run

the  machine  at  a  slight  angle  to  the  rows.  This  will

improve  trash  flow  and  help  spread  the  residue  more

evenly throughout the field.

11. Remove the transport pins and unfold machine. Make sure

the fold cylinders are fully extended to allow the wings to

fully flex in the field.

12. The  ideal  working  speed  for  the  Ultra-Till  with  turbo

blades is 7 to 10 mph and with disc blades, no more than 7

mph is recommended due to the possibility of ridging.

13. Before starting in the field: Set the depth of the gangs at 0

inches on the gauge. Let the machine all the way down

until the cylinders are retracted. Set your leveling front to

back with the turnbuckle on the hitch by lengthening or

shortening. Reset the depth of gangs between 2 to 3 on the

level gauge.

Hydraulic Down Pressure 3030

Refer to Figure 8

This setup procedure is for tractors with closed-center

or  pressure  compensated  flow  hydraulic  systems.

Open center hydraulics not supported. Adjust down

pressure valve as shown on decal (1) (located on top

of pressure reducing valve) 

Refer to Figure 9

.

14. Close front valve (2) (clockwise); open one turn.
15. Set tractor flow rate for fold system to SLOW.
16. Engage hydraulics (continuous flow) down.
17. Adjust rear valve (3) to obtain 1400 psi.
18. Adjust front valve (2) to 1300 psi; lock valve.
19. Adjust  rear  valve  (3)  to  desired  down  pressure  (usually

between 500 to 800 psi). 

20. If the wings run high during operation, increase pressure.

If the center runs high, decrease pressure. Do not exceed

exceed 1000 psi.

Caution: This  machine  is  designed  for  continuous  hydraulic

flow to the wing fold cylinders during field operations. It is for

use on tractors having CLOSED CENTER hydraulics only. If

your  tractor  has  OPEN  CENTER  hydraulics,  please  consult

your dealer for operating instructions.

2

3

1

Figure 8

Down Pressure 3030

43177

Figure 9

Down Pressure Decal 3030

838-981C

Содержание Ultra-Till I 3030 Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды