4
will also be required to power the receiver. Be sure to follow the
ESC instructions for using a separate power source (voltage
regulator or receiver battery) for the receiver.
3D Set-Up
❍
Great Planes ElectriFly LiPo 4S 14.8V 2200 mAh 30C
discharge w/balance plug [GPMP0862]
❍
FlightPower LiPo Pro50 4S 14.8V 2550 mAh 50 C
[FPWP5041]
❍
APC 12
6E Propeller (APCQ4130)
❍
ElectriFly Voltage Regulator (GPMM1920)
❍
Great Planes Parallel ESC Adapter Deans
®
Ultra
Plug
®
Connector (GPMM3141)
Optional Pilot
❍
Williams Brothers 1/4 Pilot Bust Kit Sportsman pilot
(WBRG1160)
ADDITIONAL ITEMS REQUIRED
Required Adhesives & Building Supplies
This is the list of adhesives and building supplies required to
fi nish the Extra 300SP EP.
Order numbers are provided in
parentheses.
❍
1/2 oz. [15g] Thin Pro CA (GPMR6001)
❍
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❍
Pro 30-minute epoxy (GPMR6047)
❍
Denatured alcohol (for epoxy clean up)
❍
Drill bits: 1/16" [1.6 mm], 5/64" [2mm], 3/32" [2.4 mm]
❍
#1 Hobby knife (HCAR0105)
❍
#11 blades (5-pack, HCAR0211)
❍
Small T-pins (100, HCAR5100)
Optional Supplies & Tools
Here is a list of optional tools mentioned in the manual that
will help you build the Extra 300SP EP.
❍
2 oz. [57g] spray CA activator (GPMR6035)
❍
CA applicator tips (HCAR3780)
❍
CA debonder (GPMR6039)
❍
Epoxy brushes (6, GPMR8060)
❍
Mixing sticks (50, GPMR8055)
❍
Mixing cups (GPMR8056)
❍
Threadlocker thread locking cement (GPMR6060)
❍
AccuThrow Defl ection Gauge (GPMR2405)
❍
CG Machine
™
(GPMR2400)
❍
21
st
Century
®
sealing iron [COCR2700]
❍
21
st
Century iron cover [COVR2702]
IMPORTANT BUILDING NOTES
●
There are three types of screws used in this kit:
Sheet Metal Screws
are designated by a number and a
length. For example #6
3/4" [19mm].
This is a number six screw
that is 3/4" [19mm] long.
Machine Screws
are designated by a number,
threads per inch,
and a length. For example
4-40
3/4" [19mm].
This is a number four screw
that is 3/4" [19mm] long with
forty threads per inch.
●
When you see the term
test fi t
in the instructions, it means
that you should fi rst position the part on the assembly
without using any glue
, then slightly modify or
custom
fi t
the part as necessary for the best fi t.
●
Whenever the term
glue
is written you should rely upon
your experience to decide what type of glue to use. When
a specifi c type of adhesive works best for that step, the
instructions will make a recommendation.
●
We recommend 30-minute epoxy only, because you will
need the working time or the additional strength.
●
Photos
and
sketches
are placed
before
the step they refer
to. Frequently you can study photos in following steps to
get another view of the same parts.
●
The Extra 300SP EP is factory-covered with Top Flite
MonoKote fi lm. Should repairs ever be required, MonoKote
can be patched with additional MonoKote purchased
separately. MonoKote is packaged in six-foot rolls, but
some hobby shops also sell it by the foot. If only a small
piece of MonoKote is needed for a minor patch, perhaps a
fellow modeler would give you some. MonoKote is applied
with a model airplane covering iron, but in an emergency a
regular iron could be used. A roll of MonoKote includes full
instructions for application. Following are the colors used
on this model and order numbers for six foot rolls.
TOPQ0203 - Yellow
TOPQ0202 - Orange
TOPQ0221 - Royal Blue TOPQ0201 - Missile Red
KIT INSPECTION
Before starting to build, take an inventory of this kit to make
sure it is complete, and inspect the parts to make sure they
are of acceptable quality. If any parts are missing or are not
of acceptable quality, or if you need assistance with assembly,
contact
Product Support
. When reporting defective or missing
parts, use the part names exactly as they are written in the
Kit Contents list.
Great Planes Product Support
3002 N Apollo Drive, Suite 1
Ph: (217) 398-8970, ext. 5
Champaign, IL 61822
Fax: (217) 398-7721
E-mail: [email protected]
