GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 126

GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 62

2018-06-19

Table of Contents

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Adjustments

58

00 Row Unit Adjustments

Refer to Figure 56 (which depicts a row unit fully
populated with all optional accessories [except
scraper and Keeton

®

] supported for use with the

Model 3S-4000/F/HD/HDF drills)

From front to back, a 00 Series row unit can include the
following capabilities (some optional):

1.

Opener height adjustment: standard
If a few rows need to run deeper, such as in tire
tracks, the arm’s pivot point may be lowered. See
“

Opener Height

” on page 60.

2.

Single Down Pressure Spring: standard
Each row unit is mounted on the drill as a pivoting
arm which allows the row unit to independently move
up and down. The adjustable spring provides the
force to get the row unit and attachments into the
soil. See “

Row Unit Down Pressure (Spring)

3.

Disc Blades: standard, 2 per row unit
Double disc blades open a furrow, creating the seed
bed. Spacers adjust the blades for a clean furrow.
See “

Disk Blade Adjustments

” on page 61.

4.

Seed delivery tube: standard
No adjustments are necessary.

5.

Disc Scraper: standard (not shown)
In sticky soils, a scraper helps keep the opener discs
operating freely. A slotted scraper is standard.
A spring-loaded carbide scraper is optional. See
“

Disk Scraper Adjustments

” on page 61.

6.

Seed firmer:
seed flap (not shown) standard:

Seed-Lok

®

firming wheel (shown)

Improves seed-soil contact. See “

Firmer Adjustment

” on page 62.

Keeton

®

seed firmer (not shown)

Improves seed-soil contact, and provides a stable
arm for a low-rate liquid fertilizer delivery tube. See
“

Seed Firmer Adjustment

” on page 62.

7.

Press wheels: standard (choice of types)
These close the seed trench. The wheels also
support the free end of the row unit, and provide the
primary control over seeding depth. See “

Depth (Press Wheel Height)

” on page 64.

Equipment Damage Risk:

Do not back up with row units in the ground. To do so will
cause severe damage and row unit plugging.

Figure 56

00 Series Row Unit

26382

«
...
60
61
62
63
64
...
»

Содержание 3S-4000































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды