GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 118

Страница: 118 / 126

2018-06-19

Table of Contents

Index

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Appendix B - Option Installation

114

Appendix B - Option Installation

Carbide Disc Scraper Installation

These instructions apply to an installation of scraper kit
part number 121-781A.

Optional carbide disc scrapers are not factory installed.
Start with row 1 (left-most row unit):

Remove one or both disc blades to gain safe access
to the mount

. Note the position of bushings and

spacers for correct re-assembly.

Remove the existing slotted scraper.

Refer to Figure 104

Select one:

802-079C HHCS 3/8-16X1 1/4 GR5

If Seed-Lok

is present, or also being mounted,

also select one:

804-013C WASHER LOCK SPRING 3/8 PLT

Place the lock washer

on the bolt

(because the

nut is not used).

Select one:

804-012C WASHER FLAT 3/8 SAE PLT

Place this flat washer on the bolt.

Select one:

890-357C SCRAPER-SPRING LOAD-AIR DESIGN

If the blades were not completely pre-assembled,
select one each:

K7090 AIR DESIGN SCRAPER LH SIDE

K7091 AIR DESIGN SCRAPER RH SIDE

K7096 SPACER AND WASHER ASSEMBLY

K7093 AIR DESIGN SCRAPER 15LB SPRING

Nest one side (

) behind the other. Connect the

spring

between the sides, using the small top

holes. Insert the spacer

from the front, with the

narrow raised center to the rear (in the large blade
holes).

Insert the bolt through the scraper blades (

)

and spacer

If no Seed-Lok

is present, select one each:

804-013C WASHER LOCK SPRING 3/8 PLT

803-014C NUT HEX 3/8-16 PLT

Secure the scraper assembly to the scraper
mount

using the lock washer

and nut

If a Seed-Lok

is present (not shown), secure the

scraper assembly to the Seed-Lok

, using a

threaded hole present in the Seed-Lok

. The hex nut

unused.

Re-mount the removed disc blade.

Figure 104

Carbide Disc Scraper Installation

19000

Содержание 3S-4000































































































































Результаты поиска

Содержание 3S-4000

Отзывы:

Похожие инструкции для 3S-4000

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-4000, Руководство оператора

Результаты поиска

Содержание 3S-4000

Отзывы:

Похожие инструкции для 3S-4000

Бренды по названию

Популярные бренды