GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 126

background image

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Adjustments

69

2018-06-19

Table of Contents

195-442M

If marker fails to reach ground when unfolded, or is
skipping Marker Speed

The procedure for adjusting marker speed is different for
single marker with needle valve and dual markers with
sequence valve.

Single Marker/Needle Valve Speed

Refer to Figure 74

A needle valve controls the folding speed. The needle
valve is near the rod end of the marker cylinder.

With tractor idling at a normal operating speed, adjust
marker folding to a safe speed. Turn adjustment knob
clockwise to reduce folding speed or counterclockwise to
increase folding speed. Excessive folding speed could
damage markers and void the warranty.

Dual-Marker/Sequence Valve Speed

There is one adjustment screw for unfolding speed
and one for folding speed

. You can identify adjustment

screws by markings stamped in valve body.

Turn adjustment screws clockwise (

: slower) to

decrease folding/unfolding speed and counterclockwise
(

: faster) to increase folding/unfolding.

With tractor idling at a normal operating speed, adjust
marker folding to a safe speed. Excessive
folding/unfolding speed could damage markers and void
the warranty.

After adjusting the folding speed, tighten jam nuts on hex
adjustment screws to hold settings.

Figure 74

Needle valve Adjustment

15625

1

2

F

S

Figure 75

Sequence Valve Adjustment

14048

«
...
71
72
73
74
75
...
»

Содержание 3S-4000































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-4000

Бренд: XAG Страницы: 24

Бренд: HAMAR LASER Страницы: 49

Бренд: Baroness Страницы: 40

Бренд: Baroness Страницы: 40

Бренд: BARKO LOADERS Страницы: 85

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Konica Minolta Страницы: 32

Бренд: Nabtesco Страницы: 26

QNET Physics and Dynamics

Бренд: Quanser Страницы: 4

Бренд: MAGSTIM Страницы: 86

C-HB-A-LB2-SCCT Series

Бренд: C-LITE Страницы: 9

X-431 Torque HD

Бренд: Launch Страницы: 3

Zen-O lite RS-00600

Бренд: GCE Страницы: 20

DeviceNet CompactPCI 1784-CPCIDS

Бренд: Allen-Bradley Страницы: 36

Бренд: Exmark Страницы: 36

Бренд: Manley Страницы: 18

Бренд: Focal Meditech Страницы: 10

Бренд: Rohm Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды