manualshive.com logo in svg

GREAT PLAINS 3S-4000, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 24

2018-06-19

Table of Contents

Index

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Preparation and Setup

20

Refer to Figure 4 and Figure 5

1.

Adjust the drill hitch to match your tractor-draw bar
height. Mount tongue jack on side of tongue. Use
jack to raise drill tongue so lowest hitch hole is
18 inches (45.7 cm) above ground level with drill
lowered to FIELD position.

Refer to Figure 5

2.

Bolt drill hitch onto drill tongue to match your
tractor-draw bar height. You can turn the hitch over
for a total of six different hitch heights. Always have
two (2) bolts in two holes of both tongue and hitch.

When hitching drill to a different tractor, check for a
difference in draw bar heights. If heights are different,
readjust hitch height accordingly.

3.

Securely attach safety chain to an anchor on a
tractor capable of pulling the drill. 

Refer to Figure 6

Use crank to raise jack foot. Remove pin and jack. Store
jack on top of tongue.

Figure 4

Jack in Lifting Location

18941

Figure 5

Heights for Various Hitch Positions - Correct Tongue Height

18956

32.0in

81.3cm

29.0in

73.7cm

26.0in

66.0cm

21.5in

54.6cm

18.5in

47.0cm

15.5in

39.4cm

18.0in

45.7cm

Figure 6

Jack on Storage Stob

18940

Содержание 3S-4000































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды