GRAUPNER ultra duo plus 80, Руководство по эксплуатации

Страница: 41 / 88

41 Operating Manual ULTRA DUO PLUS 80

TEMP.MODE : °C
BUTTON SOUND : ON
FINISH SOUND : 5sec
MELODY : 1

INPUT VOLT: 13.200V
OUTPUT VOLT: 11.123V
BAT. TEMP. : No.Sens
PEAK TEMP. : 0.0°C
[ 1 ]CAPACITY VOLTAGE
C: 0mAh 0.000V
D: 0mAh 0.000V
Mode
ESC
Mode
ESC
Mode
ESC
MEMORY SET
display
USER SET
display
DATA VIEW
display
CYCLE VIEW
display
3S=11.845V 1S=3.944V
33.95V
13.94V
8mV
3
1
Mode
ESC
BALANCER VIEW
display
1

TEMP.MODE : °C
BUTTON SOUND : ON
FINISH SOUND : 5sec
MELODY :

INPUT VOLT: 13.200V
OUTPUT VOLT: 11.123V
BAT. TEMP. : No.Sens
PEAK TEMP. : 0.0°C
[ 1]CAPACITY VOLTAGE
C: 0mAh 0.000V
D: 0mAh 0.000V
1

11] LiPo 3S 2200mAh
STORE MODE START
CHG.
: 2.1A
4.20V/C
DCHG. : 10.0A 3.0V/C

0 ] NiMH 6S 3300mAh
CYCLE : C-> D 1X 10m
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C

0 ] NiMH 6S 3300mAh
CYCLE : C->
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C

0 ] NiMH 6S 3300mAh
CYCLE : C->
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C

0 ] NiMH 6S 3300mAh
CYCLE : C->
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C

0 ] NiMH 6S 3300mAh
CYCLE : C->
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C

0 ] NiMH 6S 3300mAh
CYCLE : C->
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C
D 1X 10m
D 1X 10m D 1X 10m D 1X 10m

0 ] NiMH 6S 3300mAh
CYCLE : C->
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C

0 ] NiMH 6S 3300mAh
CYCLE : C->
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C
D 1X 10m
11. Supplementary screen displays
In the active screen area (standard appearance) you can switch
between the various displays using the MODE or ESC button. The
settings apply to the selected charge output only.
User settings:
This display enables the user to select the temperature display (TEMP MODE: °C or °F), the button beeps (BUTTON
SOUND: on / off), the length of the melody (FINISH SOUND: on / off, 15 sec.- 1 min.) and the melody (MELODY 1 - 9) which
is to sound at the end of the charge process. We recommend that you select different melodies for the two charge outputs,
so that you can immediately tell from the tune which battery is fully charged.
Data view:
This display shows the charger’s input voltage (INPUT VOLT) and output voltage (OUTPUT VOLT), and - if the temperature
sensor is connected - the actual temperature (BAT.TEMP) and maximum temperature (PEAK TEMP.) of the selected charge
output.
Cycle view:
This display shows the charge data (C) and discharge data (D) for the last battery which was cycled at this output. The
display shows charged-in and discharged capacity in mAh and voltage in V.
Note: the Cycle menu is only available for NiCd and NiMH batteries; you can view the data for the last ten cycles by pressing
the INC button.