background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved. No liability for printing errors.               06/2010 

24 

 

Manufacturer’s declaration: 

If material defects or manufacturing faults should arise in a product distributed by us 
in the Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, 
Graupner  GmbH  &  Co.  KG,  Henriettenstraße  94-96,  D-73230  Kirchheim/Teck,  Ger-
many,  acknowledge  the  obligation to  correct  those  defects  within  the  limitations de-
scribed below. 
The consumer is not entitled to exploit this manufacturer’s declaration if the failure in 
the usability of the product is due to natural wear, use under competition conditions, 
incompetent or improper use (including incorrect installation) or external influences. 
This  manufacturer’s  declaration  does  not  affect  the  consumer’s  legal  or  contractual 
rights  regarding  defects  arising  from  the  purchase  contract  between  the  consumer 
and the vendor (dealer). 
 
Extent of the guarantee 
 
If  a  claim  is  made  under  guarantee,  we  undertake  at  our  discretion  to  repair  or  re-
place the defective goods. We will not consider supplementary claims, especially for 
reimbursement  of  costs  relating  to  the  defect  (e.g.  installation  /  removal  costs)  and 
compensation for consequent damages unless they are allowed by statute. This does 
not affect claims based on legal regulations, especially according to product liability 
law. 
 
Guarantee requirements 
 
The purchaser is required to make the guarantee claim in writing, and must enclose 
original  proof  of  purchase  (e.g.  invoice,  receipt,  delivery  note)  and  this  guarantee 
card.  He  must  send  the  defective  goods  to  us  at  his  own  cost,  using  the  address 
stated above. 
The purchaser should state the material defect or manufacturing fault, or the symp-
toms of  the fault,  in  as  accurate  a manner as  possible,  so  that  we  can  check  if our 
guarantee obligation is applicable. 
The goods are transported from the consumer to us and from us to the consumer at 
the risk of the consumer. 
 
Duration of validity 
 
This declaration only applies to claims made to us during the claim period as stated 
in  this  declaration.  The  claim  period  is  24  months  from  the  date  of  purchase  of  the 
product by the consumer from a dealer in the Federal Republic of Germany (date of 
purchase).  If  a  defect  arises  after  the  end  of  the  claim  period,  or  if  the  evidence  or 
documents required according to this declaration in order to make the claim valid are 
not  presented  until  after  this  period,  then  the  consumer  forfeits  any  rights  or  claims 
from this declaration. 
 
Limitation by lapse of time 
 
If we do not acknowledge the validity of a claim based on this declaration within the 
claim period, all claims based on this declaration are barred by the statute of limita-

Содержание piper cherokee 9589


























Отзывы: