GRAUPNER piper cherokee 9589 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 25

background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors. 06/2010

14

Install  the  nosewheel  steering  servo  in  the  forward  servo  plate  using  the  retaining
screws supplied in the accessory pack.

Fix the noseleg in the bracket by tightening the screw in the collet. Install the nose-
wheel steering cables as shown in the photographs.
As with the other control systems, it is important to check that the nosewheel is ex-
actly  at  the  ‘straight  ahead’  position  when  the  steering  servo  is  at  centre.  Later  the
nosewheel steering servo and the rudder servo can be connected to separate chan-
nels and superimposed using a mixer at the transmitter.
The  nosewheel  spat  can  now  be  attached  to  the  yoke  of  the  noseleg  unit.  Drill  two
mounting holes in the spat as shown in the left-hand photo below. Take care to posi-
tion the spat correctly, i.e. to drill the holes in the correct side of the moulding.

«
...
12
13
14
15
16
...
»

Содержание piper cherokee 9589


























Отзывы:

Нет отзывов

Похожие инструкции для piper cherokee 9589

Бренд: Faller Страницы: 4

Premier SD50 Diesel Engine

Бренд: MTHTrains Страницы: 47

Bbaby Mini Woofer BX1986

Бренд: Maison Battat Страницы: 2

Бренд: Viessmann Страницы: 3

BABY born Brother Soft Touch

Бренд: Zapf Creation Страницы: 60

Star Wars The Black Series Mace Windu Ep3 Force FX Lightsaber

Бренд: Hasbro Страницы: 2

HLI8601 F-86 Sabre Skyblazers

Бренд: Hobby-Lobby Страницы: 10

Happy Cruisers BX1781Z

Бренд: B.toys Страницы: 2

Brainy Baby Number Bug

Бренд: VTech Страницы: 9

Mi-24V Hind armament set

Бренд: Eduard Страницы: 2

Fishbellied bridge

Бренд: Faller Страницы: 4

Бренд: Fisher-Price Страницы: 16

Interior Kit T-60

Бренд: MiniArt Страницы: 18

Knock Down Blocktown

Бренд: Spin Master Страницы: 5

Бренд: PLAYTIVE JUNIOR Страницы: 16

Waterboard mini pondflyer

Бренд: Stevens Aero Model Страницы: 25

Me 262A Schwalbe

Бренд: Eduard Страницы: 5

Бренд: Dancing Wings Hobby Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды