GRAUPNER piper cherokee 9589 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 25

background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors. 06/2010

16

Fix the engine mounts to the firewall using the screws supplied in the kit.
Assemble the parts for the throttle servo mount, and glue the completed mount in the
slots in the firewall. Install the servo when the glue has set hard.

Install the pull-cable carburettor linkage as shown in the photo.

The ignition unit for the G 26 should be screwed to the firewall on the left-hand side.

«
...
14
15
16
17
18
...
»

Содержание piper cherokee 9589


























Отзывы:

Нет отзывов

Похожие инструкции для piper cherokee 9589

Бренд: T&J Страницы: 11

Бренд: B Страницы: 2

Бренд: Ozone Страницы: 20

Бренд: Vollmer Страницы: 4

Бренд: Black Horse Model Страницы: 20

CRUISE SHIP ALL-WEATHER

Бренд: Poly Pong Страницы: 16

Бренд: Fisher-Price Страницы: 6

Бренд: Raptor Страницы: 41

Бренд: Quick Страницы: 32

BUILD & REBUILD 10660

Бренд: LEGO Страницы: 24

Бренд: Velleman Страницы: 9

Бренд: Fisher-Price Страницы: 6

Education ROLLER COASTER PHYSICS

Бренд: K'Nex Страницы: 10

N-Strike Mega Bulldog

Бренд: Nerf Страницы: 2

Бренд: marklin Страницы: 8

Бренд: marklin Страницы: 24

Бренд: Nerf Страницы: 2

Бренд: Hasbro Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды