GRAUPNER MICRO MAGIC Скачать руководство пользователя страница 18

Care and maintenance  
Especially with the first sailing please take sometimes the boat out of the water and check 
that all screws have not become loose, not interlocked ropes, no knots solved and no water is 
in the boat. Small amounts of moisture inside the boat, especially when used in the rain or 
strong wind and waves are normal and can be easily recorded and eliminated with a paper 
towel or a sponge.  
Immediately after sailing please take the tension out of your sails. For this purpose you 
should relax the backstay and relieve the luff at main sail. If after that there is still tension on 
the luff of the jib, please be sure to relieve this too. If you have driven with strong bent mast 
and little twist in bulk, you may need to twist after releasing the backstay and the press-down 
device to relieve the leech of the mainsail.  
Open the cabin cover, remove the battery and any wet cloth or sponge.  
Wipe the boat with a soft cloth and put it to dry on the boat stand.  
For a longer break, you can also dismantle the keel and remove the water from the keel and 
the mast support.  
Check from time to time, the ropes for damage. Damaged ropes should be replaced for safe-
ty‘s sake.  
Approximately twice a year you should lubricate the rudder shaft and the thread of the press-
down. 

After sailing 

Now all that remains is  
                   to wish you to have fun sailing your model ! 

10/2015 

Содержание MICRO MAGIC



















Отзывы: