background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY 

Modifications reserved! No liability for printing errors!  

 

 

     10/2011 

 

- 16 - 

Check that the control surfaces follow the movement of the transmitter joysticks. 
 
After each session, remove the battery from the model, discharge it to the recommended level, 
and store it in a safe place, well out of the reach of children, at a temperature in the range 
about +5°C to +25°C. 

 

 
These  notes  are  intended  only  to  make  you  aware  of the  many  dangers and  hazards  that  can 
arise  if  you  work  carelessly  or  irresponsibly.  If  you  take  reasonable  care,  model  flying  is  a 
highly creative, instructive, enjoyable and relaxing pastime. 
 
Manufacturer’s declaration: 
If  material  defects  or  manufacturing  faults  should  arise  in  a  product  distributed  by  us  in  the 
Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, Graupner GmbH & 
Co.  KG,  D-73230  Kirchheim/Teck,  Germany,  acknowledge  the  obligation  to  correct  those 
defects within the limitations described below. 
 
The  consumer  is  not  entitled  to  exploit  this  manufacturer’s  declaration  if  the  failure  in  the 
usability of the product is due to natural wear, use under competition conditions, incompetent 
or improper use (including incorrect installation), or external influences. 
 
This  manufacturer’s  declaration  does  not  affect  the  consumer’s  legal  or  contractual  rights 
regarding  defects  arising  from  the  purchase  contract  between  the  consumer  and  the  vendor 
(dealer). 
 
Extent of the guarantee  
If  a  claim  is  made  under  guarantee,  we  undertake  at  our  discretion  to  repair  or  replace  the 
defective  goods.  We  will  not  consider  further  claims,  especially  for  reimbursement  of  costs 
relating  to  the  defect  (e.g.  installation  /  removal  costs)  and  compensation  for  consequent 
damages  unless  they  are  allowed  by  statute.  This  does  not  affect  claims  based  on  legal 
regulations, especially according to product liability law. 
 
Guarantee requirements  
The  purchaser  is  required  to  make  the  guarantee  claim  in  writing,  and  must  enclose  original 
proof of purchase (e.g. invoice, receipt, delivery  note) and this guarantee card. He must send 
the defective goods to us at his own cost, using the address stated above.  
 
The purchaser should state the material defect or manufacturing fault or the symptoms of the 
fault  in  as  accurate  a  manner  as  possible  so  that  we  can  check  whether  our  guarantee 
obligation is applicable. 
The goods are transported from the consumer to us and from us to the consumer at the risk of 
the consumer. 
 
Duration of validity  
This  declaration  only  applies  to  claims  made  to  us  during  the  claim  period  as  stated  in  this 
declaration.  The  claim  period  is  24  months  from  the  date  of  purchase  of  the  product  by  the 
consumer  from  a  dealer  in  the  Federal  Republic  of  Germany  (date  of  purchase).  If  a  defect 
arises after the end of the claim period, or if the evidence or documents required according to 
this declaration in order to make the claim valid are not presented until after this period, then 
the consumer forfeits any rights or claims from this declaration. 
 
Limitation by lapse of time  
If we do not acknowledge the validity of a claim based on this declaration within the claim 
period, all claims based on this declaration are barred by the statute of limitations after six 
months from the time of claim, but not before the end of the claim period.  
 
Applicable law  
This declaration, and the claims, rights and obligations arising from it, are based exclusively 
on the applicable German Law, without the norms of international private law, and excluding 
UN retail law. 

Содержание LEKI EXTRA 330SC

















Отзывы: