background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

 

We reserve the right to introduce modifications. Not liable for printing errors!               

12/2011

 

20 

  If there are passers-by or spectators at your flying site, make sure that they 

are  aware  of  the  dangers  inherent  in  your  activity  before  you  start  the 
motor, and insist that they keep a safe distance away (at least 5 m). 

  Model  aircraft  may  be  flown  only  at  "normal"  outside  temperatures, 

meaning in a range of - 5º C to + 35º C; more extreme temperatures can lead 
to changes, for example in battery capacity and material characteristics, et 
cetera. 

  Model fuel is poisonous! Do not let it come into contact with eyes or mouth! 

Store only in clearly marked containers out of the reach of children. 

  Never run the motor in closed rooms, such as basement, garage, et cetera. 

Model motors also produce deadly carbon monoxide gas.  

  Operate only outdoors! 

  Adhesives and paints contain materials which may be hazardous to health 

under  certain  circumstances.  You  should  therefore  observe  the  notes  and 
warnings supplied by the manufacturers of these materials. 

  Model  fuel  is  highly  flammable  and  combustible;  keep  away  from  open 

flames,  excessive  heat,  any  sources  of  sparks  or  other  things  that  could 
lead to ignition. Do not smoke in the direct vicinity of fuel or fuel fumes.
 

  During  operation,  a  model  motor  develops  a  great  deal  of  heat.  Motor  and 

shock  absorbers  are  therefore  very  hot  during  operations  and  for  a  while 
afterwards.  Touching  them  can  result  in  serious  burns.  Careful  when 
making  adjustments!  Wear  protective  gloves!  In  extreme  cases,  even  fires 
can be caused.
 

  While  operating  the  motor,  not  only  poisonous  and  hot  exhaust  emanates 

from  the  exhaust  pipe  but  also  very  hot  liquid  combustion  residue,  which 
can result in burns.
 

  After operation, remove residual fuel from the tank and motor. 

  Every  time  you  intend  to  operate  your  model,  check  carefully  it  and 

everything  attached  to  it  (for  example  propellers,  control  surface  linkages, 
rudders,  et  cetera)  for  possible  damage.  If  you  find  a  fault,  do  not  fly  the 
model until you have corrected it.
 

  The motor is started with an electric starter, which may be equipped with an 

adapter  that  fits  the  model.  For  fixed-wing  aircraft,  startup  aid  can  also  be 
provided, for example, by a wooden rod with a piece of water hose attached.
 

  During  operation,  model  motors  may  develop  noise  far  greater  than  85  dB 

(A);  always  wear  protection  for  your  ears.  Never  start  motors  without  a 
silencer.  However,  even  with  a  silencer,  model  motors  can  disturb 
neighbours. Don’t run motors when people expect peace and quiet.
 

  If the propeller is turning while the model is standing on sandy ground, for 

instance, the propeller can suck up sand and dust and hurl it around, and it 
could get in people's eyes. Wear protective goggles!
 

  Take  care  that  the  spark  plug  clip  and  the  lead  can  not  get  tangled  in  the 

turning propeller or other rotating parts.  Check the throttle linkage, too. 

  Take particular care when carrying the model with the engine running. Hold 

the rotating parts well away from you!  

  Always  keep  an  adequate  supply  of  fuel  in  the  tank.  Never  continue  to  fly 

the model until all the fuel is used up. 

  Never fly directly over people. 

Содержание BO 209 MONSUN

























Отзывы: