GRASS VALLEY Kudos Pro LC4000 Скачать руководство пользователя страница 18

Страница: 18 / 83

Introduction

Order Codes

Order Codes

The following product order codes are covered by this manual:

Interface Card Rear Panel View

Feature Summary

• Handles up to 12 SDI signals over dual 10GbE IP links (dependent on SDI signal format and

compressed/uncompressed transport mode).

• Supports configuration of Ethernet links for maximum signal transport using both SFPs, or

for dual link mode to provide link redundancy as per SMPTE 2022-7.

• Multiple transport types available for each SDI input, including:

• Compressed IP transport using SMPTE-2042 (VC2) low latency high quality encoding

profile.

• Uncompressed video transport using either VSF TR-03 and TR-04 RTP (upgradeable to

SMPTE 2110), or SMPTE-2022-6 encapsulation.

• PCM audio using TR-03 & AES67.
• SMPTE-291M metadata support via IETF standard

RTP Payload for Ancillary Data.

• Supports frame synchronized SDI outputs referenced to IEEE-1588v2 (PTP) network timing

(compliant with SMPTE-2059-2) for black burst/tri-level syncs.

• Low delay mode and Independent H & V offset available for each channel along with up to

2 frames of video delay, and up to 255ms of audio delay.

• Supports uni-cast as well as IGMPv3 source specific multi-cast, allowing point to point

operation or transmission in multi-cast groups.

• Standards supported:

• 3G-SDI to SMPTE 424M/425M level A compatible.
• HD-SDI to SMPTE292M/274M/296M.
• SD-SDI to SMPTE259M-C.
• 10G Ethernet to IEEE 802.3.

• RollCall control and monitoring compatible, with standard logging and reporting features.

Kudos Pro-IP-LC

Quad-channel Linear Motion Adaptive Standards Converter with IP
Interfacing.

Kudos Pro-IP-MC

Dual-channel Motion Compensated Standards Converter with IP
Interfacing.

Kudos Pro-IP-SV

Quad-channel Linear Motion Adaptive Format Converter and
Synchronizer with IP Interfacing.

IQMIX10KP

Содержание Kudos Pro LC4000




















































































Результаты поиска

Содержание Kudos Pro LC4000

Отзывы:

Похожие инструкции для Kudos Pro LC4000

Бренды по названию

Популярные бренды

GRASS VALLEY Kudos Pro LC4000, Руководство пользователя

Результаты поиска

Содержание Kudos Pro LC4000

Отзывы:

Похожие инструкции для Kudos Pro LC4000

Бренды по названию

Популярные бренды