GRASS VALLEY CR6400 Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 68

background image

17

CR6400

User’s Guide

router. Tabs at the ends of the control panel fit in slots in the face of the router, helping you
align the panel to the router.

As you install the panel, its buttons might flicker until you secure the panel in place. This is
harmless.

You may install a control panel’s button legends at any time. See

Button Legends

on

page 22.

3 Mount, and secure, the router assembly in the rack.

The CR6400 router’s mounting holes on each side are spaced 3” (76mm) vertically and allow
approximately 1/8” (3mm) of play horizontally.

Position the router so that its mounting holes are aligned with the holes in the rack. Use 4
screws to secure the router to the rack.

4 If you are using the router on a network, connect the supplied Ethernet cable (RJ-45) from

the network switch to the Ethernet port of the router.

See

Creating a Router Network

, on page 18.

5 Optionally, connect your video reference.

SDI signals require a reference to perform switches in accordance with SMPTE RP168.

The router has two video reference BNC connectors. You can connect the reference source to
either one. If you have more than one router, you can “daisy chain” the output of one refer-
ence connector to the input of another. The output of the last connector in the series should
be terminated with a 75

W

BNC terminator.

6 Optionally connect the ground lug to earth ground. Use copper wire from 14 to 6 AWG.

Grounding decisions are left to you or your facilities manager. Failure to connect the ground
will not affect normal operation, but connecting the ground will protect you and your equip-
ment in a power anomaly such as a lightning strike.

7 Connect one or both power supplies.

The external power supplies are described in

Power Specifications

on page 35. Each connec-

tor has 4 pins.



The enclosing ring of the cable connectors are connected to ground. Be careful not to
short the power pins (+48V) to the ring.



Always disconnect the power supply from AC power before connecting the power
supply to the router. Then reconnect AC power to the power supply.

See

Trouble-Shooting

on page 33 if the power LED on the front of the router (or control

panel) fails to light.

8 Connect input devices and output devices. The exact connections are, of course, determined

by the requirements of your system.

The AES and 3Gig cards have DIN 1.0/2.3 connectors. Depending on the devices you are con-
necting to your router, you might need to obtain BNC-to-DIN adapter cables.

Following are recommended practices for installing CR6400 routers:

•

If the router is installed in a closed or multi-unit rack assembly, the operating ambient tem-
perature of the rack environment may be greater than room’s ambient temperature. Install
the router in an environment compatible with the maximum ambient temperature (Tma)
specified for the router.

«
...
25
26
27
28
29
...
»

Содержание CR6400 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для CR6400 Series

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Elinx EIRP305-T

Бренд: B&B Electronics Страницы: 19

Бренд: NETGEAR Страницы: 14

Бренд: DPtech Страницы: 39

Бренд: KPN Страницы: 14

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Бренд: Kanguru Страницы: 13

Бренд: Freund Страницы: 6

Бренд: 3Com Страницы: 12

Бренд: MSNswitch Страницы: 2

Бренд: TP-Link Страницы: 4

Бренд: Vaisala Страницы: 32

ipRocketLink 3101 Series

Бренд: Patton Страницы: 119

Sporlan Division SCS-PB Series

Бренд: Parker Страницы: 10

Бренд: ADC Страницы: 29

Бренд: Lanpro Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды