Graco LineDriver 25U670 Скачать руководство пользователя страница 7

Страница: 7 / 40

Setup

3A9034B

Setup

1. Install supplied ramp onto pallet.

2. Connect Hitch Receiver to line striping or line

removal equipment -

Hitch Receiver Kit 25N787;

Manual 3A6720.

3. Install LineDriver Coupler to striper or grinder hitch

ball.

4. Latch Coupler to locked position (M).

NOTE:

If Coupler is too tight to latch or is loose after

latching, Coupler needs adjustment. Refer to

Coupler

Adjustment

, page 16.

5. Insert safety pin in latch

6. Adjust seat forward/backward with lever below seat.

7. Adjust height of pedals to desired position by

removing/replacing bolts (Y).

8. Loosen two bolts (C) on topside of pedals. Rotate

pedal to desired position. Tighten bolts.

12V Auxiliary Ports

12V auxiliary power ports are provided to power

accessories.

ti11087a

ti10936a

NOTICE

12V auxiliary ports must be used to power

accessories. Battery damage can result if other means

are used to power accessories.

ti11086a

ti11085a

Содержание LineDriver 25U670









































Результаты поиска

Содержание LineDriver 25U670

Отзывы:

Похожие инструкции для LineDriver 25U670

Бренды по названию

Популярные бренды

Graco LineDriver 25U670, Операция - Ремонт - Запчасти

Результаты поиска

Содержание LineDriver 25U670

Отзывы:

Похожие инструкции для LineDriver 25U670

Бренды по названию

Популярные бренды