Graco Husky 2200 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 34

background image

6. Install the o-ring (214♦) on the cup (213♦). Apply

a light ﬁlm of grease to the outside surface of the

o-ring and the inside mating surface of the base

(212♦).

Orient the end of the base that has a magnet

toward the end of the cup that has the larger

cutout. Engage the opposite end of the parts.

Leave the end with the magnet free. Tilt the base

toward the cup and fully engage the parts, using

care so that the o-ring remains in place. Align the

magnet in the base with the air inlet and install

the cup assembly.

7. Grease the cup side and install the valve plate

(205♦). Align the small hole in the plate with the

air inlet. Tighten the screws (209♦†) to hold it in

place.

Apply lithium-

based grease.
U-cup lips must

face piston.
Apply lithium-

based grease to

contact surface.
Air inlet.

3A2714B

13

«
...
11
12
13
14
15
...
»

Содержание Husky 2200



































Отзывы:

Нет отзывов

Похожие инструкции для Husky 2200

Бренд: DAB Страницы: 8

Бренд: Zehnder Rittling Страницы: 4

Бренд: Zazen Страницы: 8

Бренд: Zip Страницы: 16

Бренд: Rheem Страницы: 28

Q HEAT R Series

Бренд: CANVAC Страницы: 88

Бренд: CTC Union Страницы: 2

Бренд: Anest Iwata Страницы: 4

Бренд: OilGear Страницы: 31

Бренд: Cosmo Страницы: 48

Бренд: Kärcher Страницы: 68

AquaMax Eco Premium 4000

Бренд: Oase Страницы: 121

Бренд: NEXT pool Страницы: 19

Colleague 3 CXE

Бренд: baxter Страницы: 230

Бренд: York Страницы: 52

AJ 4 Plus 95/40

Бренд: T.I.P. Страницы: 140

Бренд: Bryant Страницы: 12

Sandpiper S20 Metallic

Бренд: Warren rupp Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды