Graco Husky 2200 Скачать руководство пользователя страница 8

Страница: 8 / 34

Troubleshooting

Troubleshooting

Problem

Cause

Solution

Pump is running too fast, causing

cavitation before prime.

Reduce air inlet pressure.

Check valve ball severely worn or

wedged in seat or manifold.

Replace ball and seat.

Seat severely worn.

Replace ball and seat.

Outlet or inlet clogged.

Unclog.

Inlet or outlet valve closed.

Open.

Inlet ﬁttings or manifolds loose.

Tighten.

Pump cycles but will not prime.

Manifold o-rings damaged.

Replace o-rings.

Pump cycles at stall or fails to hold

pressure at stall.

Worn check valve balls, seats, or

o-rings.

Replace.

Air valve is stuck or dirty.

Disassemble and clean air valve.

Use ﬁltered air.

Check valve ball severely worn and

wedged in seat or manifold.

Replace ball and seat.

Pilot valve worn, damaged, or

plugged.

Replace pilot valve.

Air valve gasket damaged.

Replace gasket.

Pump will not cycle, or cycles once

and stops.

Dispensing valve clogged.

Relieve pressure and clear valve.

Clogged suction line.

Inspect; clear.

Sticky or leaking check valve balls.

Clean or replace..

Diaphragm (or backup) ruptured.

Replace.

Restricted exhaust.

Remove restriction.

Pilot valves damaged or worn.

Replace pilot valves.

Air valve damaged.

Replace air valve.

Air valve gasket damaged.

Replace air valve gasket.

Air supply erratic.

Repair air supply.

Pump operates erratically.

Exhaust mufﬂer icing.

Use drier air supply.

3A2714B

Содержание Husky 2200



































Результаты поиска

Содержание Husky 2200

Отзывы:

Похожие инструкции для Husky 2200

Бренды по названию

Популярные бренды

Graco Husky 2200, Запасные части

Результаты поиска

Содержание Husky 2200

Отзывы:

Похожие инструкции для Husky 2200

Бренды по названию

Популярные бренды