background image

Operation

3A5581C

17

Cutting Material

1. Start Engine, see page 16.

2. Turn vacuum on, if using a vacuum. 

Adjusting Cutter Head Angle

1. Locate a level surface for cutter adjustment. All four 

wheels should be on a level surface for setup.

2. Run at about 1/3 engine throttle.

3.

Non-DCS Models: 

Lower the Cutter Head Engage 

Lever. 

4.

Non-DCS Models: 

Slowly lower the Cutter Head 

Adjustment Dial and at first sign of dust from the 
cutters, raise the depth control knob up a couple of 
turns and then lift the Cutter Head Engage Lever 
back up.

DCS Models: 

Slowly lower the cutter head by pressing 

the Down Button on the DCS Control repeatedly until the 
first sign of dust from the cutters. Then raise the cutter 
head off of the surface by pressing the Home Button.

5. Move the machine away from the current position to 

inspect the cut. Use the elevation screws in the front 
of the machine to pitch the cutter to the correct 
plane to create the desired cut pattern. Loosen bolts 
A and B, then adjust bolt C to modify the cutter head 
angle. Tighten bolts A and B when the desired 
cutter angle is achieved. 

Maintain a safe operating distance from other people 
in the work area. Avoid any pipes, columns, openings, 
or any other objects protruding from your work sur-
face.

C

B

A

Содержание 25M847



























































Отзывы: