background image

Setup 

18

3A5354B

System Heat Up

NOTE: 

Operate at the lowest temperature and pressure 

necessary for your application.

1. Turn the main power switch (MP) on the electrical 

control panel door to the ON position. See F

IG

. 17.

2. Press the On/Off key 

 while in the Heat Run 

screen to turn the heaters on for the enabled heat 
zones.

3. Press 

 on the ADM to set up the warm melt 

zones. Press 

 to set up the Zone type. Select 

Zone Type and set the temperature. Press 

 to 

complete the setup.

4. Press 

 or 

 to activate the zone for warm 

melt running. The light will change from yellow to 
green. The alarm light will also be lit as the zone is 
heating.

5. Press the left horizontal arrow 

 to go into the 

Diagnostic screen. Information on the system heat-
ing can be seen here.

To prevent skin injection and splashing fluid from a 
burst hose, never pressurize the system while using 
warm melt materials before turning on heat.

Many warm melt materials tend to expand when 
heating and may cause a heated hose to burst. 
Avoid the potential of bursting a hose by opening 
the dispense valve during system heat up and lock-
ing the dispense valve trigger open every time you 
shut the system down.

F

IG

. 17: Power Switch ON

I   ON

O   OFF

MP

Содержание 25D117



















































Отзывы: