background image

Repair

3A5354B

31

Displacement Lower

Remove Displacement Lower

Refer to your Check-Mate Displacement Pump manual 
to repair the displacement lower.

If the air motor does not require servicing, leave it 
attached to its mounting. If the air motor does need to 
be removed, se

Remove Air Motor

, page 30.

1. Perform the 

Pressure Relief Procedure

 on page 

20 and follow the Pressure Relief Procedure in your 
pump manual.

2. Disconnect the blow off tube from the blow off valve.

3. Disconnect the cable connector (DH) from the 

platen receptacle (DG) and lower shroud recepta-
cle.

4. To remove shrouds and lower heater components, 

follow steps 1-4 on page 25.

5. Remove the screws and lock washers on the lower 

mounting rods. See F

IG

. 30.

6. Remove the quick coupler.

7. Open the main air ball valve (BA), then jog the direc-

tion valve UP to separate the lower and the air 
motor. Lift the air motor to the highest position, and 
move the lower with the platen down from the ram 
base.

8. Loosen the set screw (Z).

9. Use two people to carefully lift out the displacement 

lower. Service the displacement lower as needed. 
See the Check-Mate Displacement Pump manual 
for instructions.

Install Displacement Lower

1. Use two people to carefully insert the replaced lower 

into the platen, then tighten the set screw (Z).

2. Connect the air inlet to the main air ball valve, then 

slightly lift the air cylinders with the air motor.

3. Move the lower with the platen onto the ram base 

and align it with the lower mounting rods.

4. Jog the direction valve DOWN to slowly drop the 

lower mounting rods into the lower.

5. Install the lock washers and screws and tighten the 

screws until they are flat against the lock washers.

6. Jog the direction valve UP to lift the platen slightly. 

Loosen the platen set screw to rotate it for adjust-
ment.

7. Reinstall the pump heater components, sensor 

components and O/T device.

8. Reinstall the pump heater shrouds (see page 34)

Secure with screws.

9. See Reconnect Displacement Pump in the 

Check-Mate Pump Packages manual.

10. Reconnect the air hose and ground wire (DA) to the 

air motor.

This procedure must be done while the system is still 
warm. The material and equipment may still be hot. 
To prevent injury from burns, use proper personal 
protection equipment.

F

IG

. 30

Screws

PH

Lower

Screw/

Mounting

Rod

Lock

Washer

F

IG

. 31

H

Valve

DH

DG

Содержание 25D117



















































Отзывы: