background image

Setup

3A5354B

17

Load Material

NOTE: 

Before loading material, ensure that there is a 

minimum overhead clearance of 20 in. (51 cm) and all 
air regulators are backed off to their full counterclock-
wise position.

1. Close all air regulators and air valves. See F

IG

. 3 on 

page 7.

2. Open the main air ball valve (BA) and set the ram 

air regulator (BB) to 40 psi (0.28 MPa, 2.8 bar). Set 
the director valve handle (BC) to the UP position 
and let the ram rise to its full height.

3. Lubricate the platen seals with grease or other lubri-

cant compatible with the fluid you will pump.

4. Remove the drum cover and smooth the surface of 

the fluid with a straightedge.

5. Put a full drum of fluid on the ram base, slide it back 

against the drum stops, and center it under the 
platen.

6. Remove the bleed stick (DE) from the platen bleed 

port. See F

IG

. 16.

7. If the drum has a plastic liner, pull it over the edge of 

the drum. Secure the liner with tape wrapped 
around the circumference of the drum.

8. Set the director valve (BC) to the DOWN position 

and lower the ram until fluid appears at the top of 
the platen bleed port. Adjust the ram air regulator 
(BB) as needed. Set the director valve (BC) to neu-
tral and close the platen bleed port (G).

NOTICE

Do not use a drum of material that has been dented or 
otherwise damaged; damage to the platen wiper can 
result.

Moving parts can pinch or amputate fingers. When 
the pump is operating and when raising or lowering 
the ram, keep fingers and hands away from the pump 
intake, platen, and lip of the drum.

F

IG

. 16: Heated Platen

G

D

DE

Содержание 25D117



















































Отзывы: