Graco 218-940 Скачать руководство пользователя страница 20

Страница: 20 / 24

ACCESSORIES

USE GENUINE GRACO PARTS AND ACCESSORIES

Must be purchased separately.

GROUNDING CLAMP 103–538

GROUND WIRE

208–950

25 ft (7.6 m) long, 12 gauge (1.5 mm

)

AIR LINE FILTER 106–148

17.5 bar (250 psi) MAXIMUM WORKING PRESSURE

Reusable 40 micron filter and drain cock.

3/8 npt(f) inlet and outlet

AIR LINE LUBRICATOR 214–847

17.5 bar (250 psi) MAXIMUM WORKING PRESSURE

For automatic air valve lubrication.

3/8 npt(f) inlet and outlet

AIR REGULATOR 202–156

21 bar (300 psi) MAXIMUM WORKING PRESSURE

0–14 bar (0–200 psi) air operating range.

3/8 npt (m x f) inlet and outlet

AIR CONTROL VALVE 205–090

Use to control pump speed by regulating air flow. Install at

pump air inlet, using 156–823 Adapter. 1/4 npsm(m) x 1/4

npsm(f) swivel.

AIR INLET ADAPTER 156–823

Install at pump air inlet to allow use of 205–090 Air Con-

trol Valve. 1/4 npt(m) x 1/4 npsm(f) swivel.

BLEED–TYPE MASTER AIR VALVE 107–142

21 bar (300 psi) MAXIMUM WORKING PRESSURE

Relieves air trapped in the air line between the pump air

inlet and this valve when closed.

1/2 npt (m x f) inlet and outlet

STAINLESS STEEL BALL CONVERSION KIT 220–987

The stainless steel balls in this kit are heavier than the

standard balls supplied in the pump, and will seat posi-

tively when you are pumping high density or high viscos-

ity fluids.

CONVERSION KIT 222–373

To convert buna–N, polyester elastomer

, or EPDM

pumps to a

diaphragm model.

DUAL INLET CONVERSION KIT 220–986

For aluminum model pump 218–940. Converts pump to

enable intake of two different fluids, to be mixed in a 1:1

proportion. See page 5 for further information.

ADAPTERS

For plumbing the exhaust air.

108–271

3/8 BSP(m) x 1/4 npt(f)

108–272

3/8 BSP(f) x 1/4 npt(f)

GROUNDED BUNA–N AIR EXHAUST HOSE

12 bar (175 psi) MAXIMUM WORKING PRESSURE

For exhausting air.

3/8 npt (mbe), 13 mm (1/2 in.) ID

214–650

1.52 m (5 ft) long

214–651

5.48 m (18 ft) long

214–655

7.62 m (25 ft) long

214–654

15.2 m (50 ft) long

214–653

30.5 m (100 ft) long

FLUID PRESSURE RELIEF KIT 800–310

For use in systems with pressure rise due to thermal ex-

pansion. Pump outlet manifold must be reversed so inlet

and outlet face the same direction.

PUMP OUTLET

803–102

RELIEF

VALVE

803–101 TEE

202–812 HOSE

(NEOPRENE)

156–823 SWIVEL

803–101 TEE

PUMP INLET

PTFE

Содержание 218-940

























Результаты поиска

Содержание 218-940

Отзывы:

Похожие инструкции для 218-940

Бренды по названию

Популярные бренды

Graco 218-940, Инструкция-перечень запасных частей

Результаты поиска

Содержание 218-940

Отзывы:

Похожие инструкции для 218-940

Бренды по названию

Популярные бренды