background image

Typical Installation

306556T

9

5.

Secure the pump to the pump mounting brackets 
(86) from the underside with screws (68).

6.

Adjust the inductor plate on the pump so the pump 
intake slots are located just below the bottom of the 
inductor plate cone (see F

IG

. 5).

7.

Tighten the lock nut (11, 24 or 114) securely.

Model 204490

Refer to F

IG

. 6 for Steps 1-3, below.

1.

Lubricate the o-ring (20) in the inductor plate (18) 
with light, waterproof grease.

2.

Guide the pump intake valve as far as possible into 
the inductor plate, then tighten the set screws (19). 

4.

Loosen the pump support brackets (83) and raise 
the support (64) until it meets the pump base.

5.

Secure the pump to the pump support mounting 
bracket (86) from the underside with screws (68).

Model 25P544

Refer to F

IG

. 5 and F

IG

. 7 for Steps 1-6 below.

1.

Position the pump mounting brackets (86), then 
tighten the set screws to secure in place.

2.

Mount the bung adapter plate (117) to the pump 
mounting brackets (86) using cap hex screws (118).

3.

Remove the inductor plate nut (114), ferrule (115) 
and the o-ring (113) (F

IG

. 5).

4.

Lower the pump tube through the bung adapter 
plate (117).

5.

Using this order, slide the inductor plate nut (114), 
ferrule (115), and the o-ring (113) on the pump riser 
tube (F

IG

. 5).

6.

Adjust the inductor plate on the pump so that the 
pump intake slots are located just below the bottom 
of the inductor plate cone (see F

IG

. 5).

7.

Tighten the lock nut (114) securely.

8.

Loosed the pump support clamps and raise the 
support (64) until the bung adapter plate (117) 
meets the bung adapter on the pump tube.

9.

Turn the bung adapter into the bung adapter plate 
until tight.

F

IG

. 6: 

18

20

19

F

IG

. 7:

117

86

bung

 

adapter

Содержание 204490





























Отзывы: