GPI GM001 Скачать руководство пользователя страница 2

2

  •  When measuring flammable liquids, observe precau-

tions against fire or explosion.

  •  When  working  in  hazardous  environments,  always 

exercise appropriate safety precautions.

  •  When applying external power to the transmitter, use 

DC power only.

  •  Disconnect  external  power  to  the  transmitter  before 

detaching or attaching input or output wires.

  •  Ground loops between sensor and user equipment can 

damage the transmitter and can be dangerous.

  •  If you cannot galvanically isolate the sensor from earth 

ground, you may need to use the transmitter’s optically 

isolated inputs.

  •  Be sure O-rings and seals are kept in good repair. 

Installation  should  be  performed  only  by  qualified 

personnel, and in accordance with local governing 

regulations.

The following installation guidelines are separated by meter 

series and mounting type.

Precision G Series:

  • 

Local 

– The GX510 4-20 mA Out with Display mounts 

directly to the 1 inch MNPT conduit connector.

  • 

Remote 

–  The  GX500  4-20  mA  Out  with  Display 

connects via an output cable as shown in the Wiring 

Diagram.

Industrial Grade G2 Series:

  • 

Local 

– The GX510 4-20 mA Out with Display requires 

the GPI Conduit Connector Kit (Part #113437-01) for 

local mounting to the G2 series meter.

  • 

Remote 

–  The  GX500  4-20  mA  Out  with  Display 

connects via an output cable as shown in the Wiring 

Diagram.

Commercial Grade A1 Series:

  • 

Local 

– The GX510 4-20 mA Out with Display requires 

the GPI Conduit Connector Kit (Part #113437-01) for 

local mounting to the A1 series meter.

  • 

Remote 

–  The  GX500  4-20  mA  Out  with  Display 

connects via an output cable as shown in the Wiring 

Diagram.

GM Oval Gear Series:

  • 

Local 

–  The  4-20  mA  Out  with  Display  is  mounted 

directly to the oval gear meter housing. 

GENERAL  INFORMATION

This  manual  will  assist  you  in  operating  and  maintaining 

the GPI electronics supplied with your GPI meter or as an 

accessory unit on both local and remote models. The GPI 

Electronics  can  be  used  in  indoor  or  outdoor  applications 

where occasional exposure to moisture is common.
  •  The 4-20 mA Out with Display is available in two ver-

sions. One indicates flowrate in units/minute and one 

in units/hour. Both indicate flow totals in gallons and 

litres.

  •  The 4-20 mA Out with Display can be used on all GPI 

models, including the Precision G series, the Industrial 

Grade  G2  series,  the  Commercial  Grade  A1  series, 

and  the  positive  displacement  GM  series  oval  gear 

meters.

Product  differences  in  this  manual  are  identified  by  either, 

Local 

or 

Remote

 as necessary.

If the meter was purchased with this display, then it will come 

calibrated from the factory for gallons “GAL” and litre “LTR”. 

Field calibration is also available.
If  the  unit  was  purchased  as  an  accessory  or  remote,  the 

calibration has not been entered and the end user will need 

to configure and calibrate the display.
The GPI 4-20 mA Out with Display is a flow totalizer and rate 

meter with industry standard current loop output. The unit is 

loop powered, and provides a 4-20 mA analog output propor-

tional to the frequency signal for communication with PLCs 

and other customer equipment. The 4-20 mA (or 0-20 mA) 

output is calibrated under actual flow conditions with simple 

push-button calibration. Auxiliary output includes 0-5 VDC.
The  microprocessor-based  electronics  have  extremely  low 

power  requirements  and  are  completely  powered  by  the

4-20 loop. The electronics provides the options of local (on 

the meter) and/or remote (up to 5,000 feet) display. Flow total 

and rate are displayed on a large 6-digit LCD readout with 

two-point floating decimal for totals from .01 to 999,999. All 

operations are easily accessed with the push buttons on the 

display front panel.

This unit is not FM Approved. Therefore, use of this 

transmitter with an approved metering system voids 

FM Approval. 

NOTE: This unit is loop powered, requiring an input power 

supply of 8.5 to 35 volts (24 VDC is recommended). 

NOTE: Setpoint calibration of the unit is required for the 4-20 

mA, 0-20 mA, and 0-5 V output options.

SAFETY  INSTRUCTIONS

INSTALLATION

CAUTION

CAUTION

Содержание GM001





















Отзывы: