manualshive.com logo in svg

Goulds A-C 2000 Series, Инструкция по эксплуатации

Поделиться
Скачать
Goulds A-C 2000 Series Скачать руководство пользователя страница 14

14

4. Place the packing base ring (6-152-0) into the
  stuffing box. Slide the stuffing box cover over
  the pump shaft, and, if applicable, bolt the
  stuffing box to the motor adapter using
  capscrews (1-904-0).
5. Install the packing (6-924-0) and, if applicable, 

the seal cage ( 6-013-0) into the stuffing 
box being sure to stagger the joints as per 
the instructions found in the general pump 
instruction section of this book.

Impeller installation
1. If the pump is equipped with mechanical seals,
  slide the spacer sleeve (1-154-0) over the shaft
  sleeve and into the stuffing box.
2. Install the impeller key into the keyway on the
  impeller side of the motor shaft.
3. Slide the pump impeller (4-002-0) onto the  

motor shaft.

4. Screw the impeller nut (4-023-0) onto the pump
  shaft until finger tight. Hold the outside diameter of 

the impeller and tighten (clockwise as viewed from 
the suction inlet) the impeller nut to 25-30 ft. lbs.

5. For pumps with mechanical seals, tighten gland
  evenly against the stuffing box.

Final assembly

NOTE: When assembling the rotating assembly to

the casing, be certain that the pump feet

are parallel to the motor feet.

1. Place the "0" ring casing seal (2-914-0) around
    the "0" ring seat on the stuffing box cover.
2. Carefully slide the motor, motor adapter, stuffing
  box assembly into the casing being sure not to
  pinch the "0" ring. Insert the capscrews (1-904-0)
  through the frame and into the casing (the large
  Series A-C 2000 pumps use capscrews and 

clamping lugs (1-937-0) to hold the motor adapter 
to the casing. Tighten opposite capscrews evenly 
around the adapter until the stuffing box has been 
drawn evenly into the casing). Then, alternately 
torque each capscrew to 25 ft. lbs.

3. If necessary, connect the suction and discharge
  piping to the pump.
4. Secure the motor foot.
5. Connect the flushing water system to the stuffing
  box.
6. If the pump is to be started, be sure flushing is
  provided to the stuffing box.
7 . Connect the power to the motor. CHECK THE
  MOTOR ROTATION.

This completes the assembly of the Series A-C 2000 
close-coupled pump.

Содержание A-C 2000 Series

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды