background image

OM-06617

SE SERIES

3

INSTALLATION

INSTALLATION

Review all SAFETY information in Section A.

Do not operate this pump where explo­
sive vapors or flammable material exist.
Death or serious injury will result.

Pumps and related equipment must be in­
stalled and operated according to all na­
tional, local and industry standards.

PREINSTALLATION INSPECTION

Before installation, inspect the pump for damage
which may have occurred during shipment. Check
as follows:

a. Inspect the pump assembly for cracks, dents,

damaged threads, and other obvious dam­
age.

b. Check for and tighten loose attaching hard­

ware.

c. The pump is furnished with a 50‐foot (15 me­

ter) long power cable. Inspect the cable for
cuts or damage.

d. Carefully read all tags, decals, and markings

on the pump assembly, and perform all duties
as indicated.

If anything appears to be abnormal, contact your
Gorman‐Rupp distributor to determine the  repair
or  updating  policy.  

Do not

 put the pump into serv­

ice until appropriate action has been  taken.

PUMP INSTALLATION

Lifting

Pump unit weights will vary depending on the mod­
el. Check the shipping tag on the unit packaging
for the actual weight. Drain the pump and remove
all customer‐installed equipment such as dis­

charge hoses or piping before attempting to lift ex­
isting, installed units.

If necessary, attach a rope or chain to the lifting
handle on the top of the pump. 

Do not 

lift the unit

by the power cable or the discharge piping. Cus­
tomer‐installed equipment such as rigid discharge
piping 

must

 be removed before attempting to lift.

Figure 1. Do Not Lift Pump by Power Cable

Do not attempt to lift the pump by the
power cable or piping. Attach proper
lifting equipment to the handle on the
pump.

Installation

Before installing the pump, clear the sump basin of
any debris or sediment. See Figure 4 for a typical
pump installation.

The sump basin must be vented in ac­
cordance with local plumbing codes.
Do not operate this pump where explo­
sive vapors or flammable material exist.
Death or serious injury will result.

Содержание SE Series















Отзывы: