Gorlitz GO 15 Series Скачать руководство пользователя

Страница: 9 / 28

1. UNCOIL CABLE TO BE INSTALLED AND LAY IN

A STRAIGHT LINE ON THE FLOOR.

2. PASS A SHORT SECTION OF ANCHOR CABLE

THROUGH DRIVE ARM.

3. SLIDE CABLE CONNECTORS TOGETHER AND

FASTEN BOTH CAP SCREWS.

4. DRIVE ARM MUST TURN COUNTER

CLOCKWISE (FACING MACHINE) WHEN

STARTING TO INSTALL CABLE.

5. LAY OUTER CABLE TURNS BY HAND TO FILL

REEL PROPERLY.

6.  START MACHINE.
7.  FEED REMAINING CABLE INTO REEL.
8.  STOP MACHINE OCCASIONALLY TO CHECK

DISTRIBUTION AND REPOSITION CABLE IF

NEEDED.

9. ATTACH CUTTING TOOL OF YOUR CHOICE.

IF YOU ARE USING OUR POWER CABLE FEEDER AND PULLER, DO NOT ALLOW TO PASS

ANY CABLE ENDS OR CABLE CONNECTORS THROUGH FEEDER, AS IT MAY DAMAGE IT.

HOW TO INSTALL A NEW CABLE

MODEL GO 68HD, GO 68, GO 62 SERIES

MODEL GO 50 SERIES

1. UNCOIL CABLE TO BE INSTALLED AND LAY IN

A STRAIGHT LINE ON THE FLOOR.

2. MAKE SURE DRIVE ARM ROTATES FREELY.
3. FEED CABLE WITH INSTALLED CABLE END

THROUGH DRIVE ARM.

4. SCREW CABLE END INTO REEL CONNECTOR.
5. FASTEN REEL CONNECTOR TO REEL WITH

BOLT.

6. DRIVE ARM MUST TURN COUNTER

CLOCKWISE (FACING MACHINE) WHEN

STARTING TO INSTALL CABLE.

7. LAY OUTER CABLE TURNS BY HAND TO FILL

REEL PROPERLY.

8.  START MACHINE.
9.  FEED REMAINING CABLE INTO REEL.
10.  STOP MACHINE OCCASIONALLY TO CHECK

DISTRIBUTION AND REPOSITION CABLE IF

NEEDED.

11. ATTACH CUTTING TOOL OF YOUR CHOICE.

MODEL GO 380/250 SERIES, GO 15

1. UNCOIL CABLE TO BE INSTALLED AND LAY IN

A STRAIGHT LINE ON THE FLOOR.

2.  MAKE SURE DRIVE ARM ROTATES FREELY.
3.  FEED CABLE THROUGH DRIVE ARM.
4.  DRIVE ARM MUST TURN COUNTER

CLOCKWISE WHEN INSTALLING CABLE.

5. START MACHINE.
6. FEED REMAINING CABLE INTO DRUM

ALLOWING ADEQUATE LENGTH OF EXPOSED

CABLE TO ATTACH FLEXIBLE LEADER

(ELEPHANT TRUNK) WHEN APPLICABLE.

7. INSTALL CABLE END AND CUTTING BLADE

(AVAILABLE ONLY FOR 3/8” DIA. CABLE) AND/

OR MAKE CABLE BENDS OF YOUR CHOICE.

Gorlitz Operating & Maintenance Manual 8

Содержание GO 15 Series





























Результаты поиска

Содержание GO 15 Series

Отзывы:

Похожие инструкции для GO 15 Series

Бренды по названию

Популярные бренды

Gorlitz GO 15 Series, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание GO 15 Series

Отзывы:

Похожие инструкции для GO 15 Series

Бренды по названию

Популярные бренды