Gorlitz GO 15 Series Скачать руководство пользователя

Страница: 6 / 28

GENERAL OPERATING INSTRUCTIONS

1. POSITION MACHINE AS CLOSE AS POSSIBLE TO CLEAN OUT. MAXIMUM 3 FEET DISTANCE BETWEEN

MACHINE AND OPENING WORKED ON.

2. ATTACH YOUR CHOICE OF CUTTING TOOL.
3. BEFORE PLUGGING EXTENSION CORD INTO RECEPTACLE MAKE SURE ON/OFF SWITCH ON MACHINE

IS IN OFF POSITION.

IF YOU ARE OPERATING ANY MACHINE WITH AN ELECTRIC FOOT SWITCH:

•  PLUG FOOT SWITCH INTO MACHINE OUTLET.
•  PUSH FEMALE END OF EXTENSION CORD INTO FOOT SWITCH.
•  PLUG MALE END OF EXTENSION CORD INTO ELECTRICAL SOURCE.
•  MOVE ON/OFF SWITCH ON MACHINE TO “ON” POSITION.
•  STEP ON FOOT SWITCH AND MACHINE WILL START RUNNING.

IF YOU ARE OPERATING ANY MACHINE WITH AN AIR FOOT SWITCH:

• STEP ON AIR BULB AND MACHINE WILL START RUNNING.

4. MOVE SWITCH TO “ON” POSITION. IN NORMAL OPERATING MODE, DRUM OR REEL MUST TURN

COUNTER CLOCKWISE WHEN THE OPERATOR FACING THE MACHINE.

• IF DRUM OR REEL TURNS CLOCKWISE, STOP MACHINE. ALL MODELS ARE EQUIPPED WITH A

FORWARD/REVERSE SWITCH LOCATED AT THE ELECTRIC CONTROL BOX. FOR MODELS GO 380/250

SERIES AND GO 15 THE FORWARD/REVERSE SWITCH IS LOCATED AT THE COVER HOUSING. ONLY

WHEN THE MACHINE COMES TO A COMPLETE STOP SWITCH THE FORWARD/REVERSE TOGGLE

SWITCH INTO THE OPPOSITE DIRECTION.

5. FEED CABLE INTO SEWER LINE SLOWLY, FEELING YOUR WAY AS YOU GO. PLACE BOTH HANDS

EQUALLY DISTANT BETWEEN MACHINE AND CLEAN-OUT. NEVER LET YOUR HANDS GO, AS YOUR

HANDS PROVIDE A GUIDE FOR THE CABLE AND PREVENT THE CABLE FROM SWINGING, BUCKLING

OR KINKING.

6. MOST IMPORTANT, KEEP THE CABLE ROTATING AT ALL TIMES.
7. WHEN YOUR CUTTING TOOL MEETS BLOCKAGE, IT WILL SLOW DOWN OR EVEN MOMENTARILY STOP

ROTATION OF CABLE. AS SOON AS YOU FEEL A RPM REDUCTION, PULL CABLE BACK IN ORDER TO

PREVENT THE CUTTING TOOL FROM GETTING HUNG UP.

8. AS SOON AS MOTOR IS AT FULL RPM AGAIN, FEEL YOUR CABLE AGAINST STOPPAGE. PUSH AND PULL

CABLE IN QUICK SUCCESSION AGAINST AND FROM OBSTRUCTION UNTIL YOU BREAK THROUGH

BLOCKAGE.

9. ONCE YOU’VE CUT THROUGH BLOCKAGE, PULL CABLE BACK FOR SEVERAL FEET. NOW PASS CABLE

THROUGH SAME STOPPAGE LOCATION AGAIN AND ADVANCE CABLE TO NEXT LARGER DRAIN LINE

CONNECTION OR TO MAIN SEWER LINE FOR A THOROUGH CLEANING JOB.

10. AFTER THE CUTTING AND CLEANING OPERATION IS COMPLETED, RETURN CABLE INTO DRUM OR REEL

WITH MACHINE RUNNING IN ORDER FOR YOUR DRIVE ARM TO DISTRIBUTE CABLE INTO DRUM OR REEL

EVENLY.

5 Gorlitz Operating & Maintenance Manual

ALWAYS KEEP AIR HOSE CLEAR OF ANY MOVING PARTS. REPLACE ANY LEAKING OR

DAMAGED COMPONENTS.

AVOID RUNNING OF MACHINE AT LOW RPM’S FOR EXTENDED PERIOD OF TIME AS THE

UNIT MAY BECOME OVERHEATED.

IF YOUR CABLE GETS HUNG UP IN A MASS OF ROOTS, ETC. SWITCH OFF MACHINE IN ORDER

TO ALLOW CABLE AND/OR REEL OR DRUM TO BACK SPIN. LET MACHINE COME TO A

COMPLETE STOP.
IF YOU ARE UNABLE TO RETRIEVE CABLE, SWITCH MACHINE INTO REVERSE AND RUN

MOMENTARILY TO ALLOW CABLE TO UNWIND FROM STOPPAGE. ONCE CABLE IS FREE, PULL

CABLE BACK FOR SEVERAL FEET, PLACE REVERSING SWITCH IN FORWARD POSITION AND

THEN START MACHINE AGAIN.

WHEN OPERATING MACHINE WITH A POWER CABLE FEEDER AND PULLER, DO NOT ALLOW

ANY CABLE ENDS OR CABLE CONNECTORS TO PASS THROUGH FEEDER AS IT MAY DAMAGE

OR BREAK THE FEEDER BEARINGS.

(EXCEPT HANDYGUN MODEL GO31)

Содержание GO 15 Series





























Результаты поиска

Содержание GO 15 Series

Отзывы:

Похожие инструкции для GO 15 Series

Бренды по названию

Популярные бренды

Gorlitz GO 15 Series, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание GO 15 Series

Отзывы:

Похожие инструкции для GO 15 Series

Бренды по названию

Популярные бренды