Gorilla Playsets Riverview Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 94

background image

Step 3: Assembling The Right Side Frame

1: Lay the left side corner posts on the ground in their proper orientation.
2: Lay the 2 x 6 x 47-1/2” bottom panel board on top of the left side corner posts at the

bottom of the corner posts. The offset holes in the sandbox board must face downward.
3: Use 5/16 x 4-1/2” hex bolts and 5/16” washers to attach the top holes of the sandbox

board to the t-nuts installed on the corner posts. The bottom holes will be used later.
4:Lay the 2 x 6 x 47-1/2” bottom panel board on top of the left side corner posts in

the middle of the corner posts. The offset holes in the bottom panel board must face

downward.
5: Use 5/16 x 4-1/2” hex bolts and 5/16” washers to attach the bottom holes of the

bottom panel board to the t-nuts installed on the corner posts. The top holes will be

used later.
6: Lay the 4 x 4 x 47-1/2” swing beam support on top of the left side corner posts. The

three countersunk holes in the middle of the swing beam support must face downward.
7:Find two torque washer place a 6-1/2” carriage bolt inside the torque washer, making

sure that the teeth are facing in the same direction as the threads of the carriage bolt.

Place the torque washer/ carriage bolt assembly into the holes of the corner post so

that the head of the carriage bolt faces what will be the inside of the fort. Use a hammer

to set the torque washer into the corner post.
8: Attach the

swing beam

support as

shown in detail

a.

6-1/2” Carriage Bolt

4 x 4 x 47-1/2”

Swing Beam Support

Torque Washer

Bolt Cap

3/8” Nut

3/8” Washer

5/16 x 4-1/2”

Hex Bolt

5/16” Washer

5/16” Washer

The three counter

sunk hole on the swing

beam support will face

down when properly

installed

2 x 6 x 47-1/2”

Bottom Panel Board

(Offset holes down)

2 x 6 x 47-1/2”

Sandbox Board

(Offset holes down)

Page 35

®

«
...
33
34
35
36
37
...
»

Содержание Riverview































































































Отзывы:

Нет отзывов

Похожие инструкции для Riverview

Бренд: Falltech Страницы: 48

Бренд: quadient Страницы: 14

Marathon Multi600

Бренд: Saeyang Страницы: 21

Бренд: Vanguard Instruments Страницы: 47

Бренд: Kellfri Страницы: 44

Бренд: STARPLAY Страницы: 12

Бренд: K Tool International Страницы: 4

Бренд: VALD Страницы: 11

Brillion WFPD38-52

Бренд: Landoll Страницы: 74

Бренд: LifeSpan Kids Страницы: 15

IMI SENSORS 682A14

Бренд: PCB Piezotronics Страницы: 17

Exterior Wash 100

Бренд: Martin Страницы: 36

Бренд: M. J. MAILLIS GROUP Страницы: 102

Бренд: Kerbl Страницы: 7

24x8 Chicken Coop Plan

Бренд: EASY COOPS Страницы: 18

Extreme Duty Root Grapple

Бренд: Blue Diamond Страницы: 12

Бренд: Chauvet Страницы: 3

Бренд: SAKI Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды